- 您现在的位置：买卖IC网 > PDF目录15288 > LT3844IFE#TRPBF (Linear Technology)IC REG CTRLR BST INV PWM 16TSSOP PDF资料下载
参数资料
| 型号： | LT3844IFE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/24页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST INV PWM 16TSSOP |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 330kHz |
| 占空比： | 95% |
| 电源电压： | 4 V ~ 60 V |
| 降压： | 是 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 是 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 带卷 (TR) |
LT3844
OPERATION
(Refer to Functional Diagram)
The LT3844 is a PWM controller with a constant frequency,
current mode control architecture. It is designed for low
to medium power, switching regulator applications. Its
high operating voltage capability allows it to step up
or down input voltages up to 60V without the need for
a transformer. The LT3844 is used in nonsynchronous
applications, meaning that a freewheeling recti?er diode
(D1 of Function Diagram) is used instead of a bottom
side MOSFET. For circuit operation, please refer to the
Functional Diagram of the IC and Typical Application on
the front page of the data sheet. The LT3800 is a similar
part that uses synchronous recti?cation, replacing the
diode with a MOSFET in a step-down application.
Main Control Loop
During normal operation, the external N-channel MOSFET
switch is turned on at the beginning of each cycle. The
switch stays on until the current in the inductor exceeds
a current threshold set by the DC control voltage, V C ,
which is the output of the voltage control loop. The voltage
control loop monitors the output voltage, via the V FB pin
voltage, and compares it to an internal 1.231V reference.
It increases the current threshold when the V FB voltage
is below the reference voltage and decreases the current
threshold when the V FB voltage is above the reference
voltage. For instance, when an increase in the load current
occurs, the output voltage drops causing the V FB voltage to
drop relative to the 1.231V reference. The voltage control
loop senses the drop and increases the current threshold.
The peak inductor current is increased until the average
inductor current equals the new load current and the output
voltage returns to regulation.
V CC /Boosted Supply
An internal V CC regulator provides V IN derived gate-drive
power for start-up under all operating conditions with
MOSFET gate charge loads up to 90nC. The regulator can
operate continuously in applications with V IN voltages up to
60V, provided the power dissipation of the regulator does
not exceed 250mW. The power dissipation is calculated
as follows:
P d(REG) = (V IN – 8V) ? f SW ? Q G
where Q G is the MOSFET gate charge.
In applications where these conditions are exceeded, V CC
must be derived from an external source after start-up.
Maximum continuous regulator power dissipation may be
exceeded for short duration V IN transients.
For higher converter ef?ciency and less power dissipa-
tion in the IC, V CC can also be supplied from an external
supply such as the converter output. When an external
supply back drives the internal V CC regulator through an
external diode and the V CC voltage is pulled to a diode
above its regulation voltage, the internal regulator is dis-
abled and goes into a low current mode. V CC is the bias
supply for most of the internal IC functions and is also
used to charge the bootstrapped capacitor (C BOOST ) via an
external diode. The external MOSFET switch is biased from
the bootstrapped capacitor. While the external MOSFET
switch is off, an internal BJT switch, whose collector is
connected to the SW pin and emitter is connected to the
PGND pin, is turned on to pull the SW node to PGND and
recharge the bootstrap capacitor. The switch stays on until
either the start of the next cycle or until the bootstrapped
capacitor is fully charged.
Current Limit/Short-Circuit
The inductor current is measured with a series sense
resistor (see the Typical Application on the front page).
When the voltage across the sense resistor reaches the
maximum current sense threshold, typically 100mV, the
TG MOSFET driver is disabled for the remainder of that
cycle. If the maximum current sense threshold is still ex-
ceeded at the beginning of the next cycle, the entire cycle
is skipped. Cycle skipping keeps the inductor currents to a
reasonable value during a short-circuit, particularly when
MOSFET Driver
The LT3844 contains a high speed boosted driver to turn
on and off an external N-channel MOSFET switch. The
MOSFET driver derives its power from the boost capaci-
tor which is referenced to the SW pin and the source of
the MOSFET. The driver provides a large pulse of current
to turn on the MOSFET fast to minimize transition times.
Multiple MOSFETs can be paralleled for higher current
operation.
V IN is high. Setting the sense resistor value is discussed
in the “Application Information” section.
3844fb
8
相关PDF资料 |
PDF描述 |
|---|---|
| RLB9012-222KL | INDUCTOR HI CURRNT RADIAL 2200UH |
| VE-B5K-EV-F2 | CONVERTER MOD DC/DC 40V 150W |
| RLB9012-182KL | INDUCTOR HI CURRNT RADIAL 1800UH |
| LTC3810HUH-5#PBF | IC REG CTRLR BUCK PWM CM 32-QFN |
| LTC3834EUFD#PBF | IC REG CTRLR BUCK PWM CM 20-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3845 | 制造商:Cooper Crouse-Hinds 功能描述: |
| LT3845_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage Synchronous Current Mode Step-Down Controller with Adjustable Operating Frequency |
| LT3845A | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage, Current Mode Switching Regulator Controller Thermal Shutdown |
| LT3845AEFE#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LT3845AEFE#PBF | 制造商:Linear Technology 功能描述:IC DC-DC CONV 500kHz TSSOP16 制造商:Linear Technology 功能描述:IC, DC-DC CONV, 500kHz, TSSOP16 |
发布紧急采购，3分钟左右您将得到回复。