- 您现在的位置：买卖IC网 > PDF目录14796 > LT3972EMSE#PBF (Linear Technology)IC REG BUCK ADJ 3.5A 10MSOP PDF资料下载
参数资料
| 型号： | LT3972EMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 3.5A 10MSOP |
| 标准包装： | 50 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.79 V ~ 30 V |
| 输入电压： | 3.6 V ~ 33 V |
| PWM 型： | 电流模式，Burst Mode? |
| 频率 - 开关： | 230kHz ~ 2.45MHz |
| 电流 - 输出： | 3.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 10-MSOP 裸露焊盘 |
| 产品目录页面： | 1332 (CN2011-ZH PDF) |
LT3972
APPLICATIONS INFORMATION
Table 1. Inductor Vendors
Step-down regulators draw current from the input sup-
VENDOR
Murata
TDK
Toko
Sumida
NEC
URL
www.murata.com
www.componenttdk.com
www.toko.com
www.sumida.com
www.nec.com
PART SERIES
LQH55D
SLF10145
D75C
D75F
CDRH74
CR75
CDRH8D43
MPLC073
MPBI0755
TYPE
Open
Shielded
Shielded
Open
Shielded
Open
Shielded
Shielded
Shielded
ply in pulses with very fast rise and fall times. The input
capacitor is required to reduce the resulting voltage
ripple at the LT3972 and to force this very high frequency
switching current into a tight local loop, minimizing EMI.
A 10μF capacitor is capable of this task, but only if it is
placed close to the LT3972 and the catch diode (see the
PCB Layout section). A second precaution regarding the
ceramic input capacitor concerns the maximum input
voltage rating of the LT3972. A ceramic input capacitor
combined with trace or cable inductance forms a high
C OUT =
V OUT SW
Ofcourse,suchasimpledesignguidewillnotalwaysre-
sult in the optimum inductor for your application. A larger
value inductor provides a slightly higher maximum load
current and will reduce the output voltage ripple. If your
load is lower than 3.5A, then you can decrease the value
of the inductor and operate with higher ripple current. This
allows you to use a physically smaller inductor, or one
with a lower DCR resulting in higher ef?ciency. There are
several graphs in the Typical Performance Characteristics
section of this data sheet that show the maximum load
current as a function of input voltage and inductor value
for several popular output voltages. Low inductance may
result in discontinuous mode operation, which is okay
but further reduces maximum load current. For details of
maximum output current and discontinuous mode opera-
tion, see Linear Technology Application Note 44. Finally,
for duty cycles greater than 50% (V OUT /V IN > 0.5), there
is a minimum inductance required to avoid subharmonic
oscillations. See AN19.
Input Capacitor
Bypass the input of the LT3972 circuit with a ceramic
capacitor of X7R or X5R type. Y5V types have poor
performance over temperature and applied voltage, and
should not be used. A 10μF to 22μF ceramic capacitor is
adequate to bypass the LT3972 and will easily handle the
ripple current. Note that larger input capacitance is required
when a lower switching frequency is used. If the input
power source has high impedance, or there is signi?cant
inductance due to long wires or cables, additional bulk
capacitance may be necessary. This can be provided with
a lower performance electrolytic capacitor.
quality (under damped) tank circuit. If the LT3972 circuit
is plugged into a live supply, the input voltage can ring to
twice its nominal value, possibly exceeding the LT3972’s
voltage rating. This situation is easily avoided (see the Hot
Plugging Safety section).
For space sensitive applications, a 4.7μF ceramic capaci-
tor can be used for local bypassing of the LT3972 input.
However, the lower input capacitance will result in in-
creased input current ripple and input voltage ripple, and
may couple noise into other circuitry. Also, the increased
voltage ripple will raise the minimum operating voltage
of the LT3972 to ~3.7V.
Output Capacitor and Output Ripple
The output capacitor has two essential functions. Along
with the inductor, it ?lters the square wave generated by the
LT3972 to produce the DC output. In this role it determines
the output ripple, and low impedance at the switching
frequency is important. The second function is to store
energy in order to satisfy transient loads and stabilize the
LT3972’s control loop. Ceramic capacitors have very low
equivalent series resistance (ESR) and provide the best
ripple performance. A good starting value is:
100
f
where f SW is in MHz, and C OUT is the recommended
output capacitance in μF. Use X5R or X7R types. This
choice will provide low output ripple and good transient
response. Transient performance can be improved with
a higher value capacitor if the compensation network is
also adjusted to maintain the loop bandwidth. A lower
3972fa
11
相关PDF资料 |
PDF描述 |
|---|---|
| LT1976IFE#PBF | IC REG BUCK ADJ 1.5A 16TSSOP |
| MAX6422XS25+T | IC MPU/RESET CIRC 2.50V SC70-4 |
| MAX6422XS19+T | IC MPU/RESET CIRC 1.90V SC70-4 |
| MAX6422XS20+T | IC MPU/RESET CIRC 2.00V SC70-4 |
| MAX6422XS21+T | IC MPU/RESET CIRC 2.10V SC70-4 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3972EMSE-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:33V, 3.5A, 2.4MHz Step-Down Switching Regulator with 75μA Quiescent Current |
| LT3972HMSE#PBF | 功能描述:IC REG BUCK ADJ 3.5A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3972HMSE#TRPBF | 功能描述:IC REG BUCK ADJ 3.5A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3972IDD#PBF | 功能描述:IC REG BUCK ADJ 3.5A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3972IDD#TRPBF | 功能描述:IC REG BUCK ADJ 3.5A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。