- 您现在的位置：买卖IC网 > PDF目录13843 > LT3972IDD#PBF (Linear Technology)IC REG BUCK ADJ 3.5A 10DFN PDF资料下载
参数资料
| 型号： | LT3972IDD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 3.5A 10DFN |
| 标准包装： | 121 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.79 V ~ 30 V |
| 输入电压： | 3.6 V ~ 33 V |
| PWM 型： | 电流模式，Burst Mode? |
| 频率 - 开关： | 230kHz ~ 2.45MHz |
| 电流 - 输出： | 3.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 10-DFN（3x3） |
LT3972
APPLICATIONS INFORMATION
Shorted and Reversed-Input Protection
RUN
15k
I L
1A/DIV
If the inductor is chosen so that it won’t saturate exces-
sively, an LT3972 buck regulator will tolerate a shorted
output. There is another situation to consider in systems
0.22μF
RUN/SS
GND
V RUN/SS
2V/DIV
V OUT
2V/DIV
where the output will be held high when the input to the
LT3972 is absent. This may occur in battery charging ap-
plications or in battery backup systems where a battery
or some other supply is diode ORed with the LT3972’s
output. If the V IN pin is allowed to ?oat and the RUN/SS
2ms/DIV
3972 F07
pin is held high (either by a logic signal or because it is
Figure 7. To Soft-Start the LT3972, add a Resisitor
and Capacitor to the RUN/SS Pin
Synchronization
To select low ripple Burst Mode operation, tie the SYNC
pin below 0.5V (this can be ground or a logic output).
Synchronizing the LT3972 oscillator to an external fre-
quency can be done by connecting a square wave (with
20% to 80% duty cycle) to the SYNC pin. The square
wave amplitude should have valleys that are below 0.3V
and peaks that are above 0.8V (up to 6V).
tied to V IN ), then the LT3972’s internal circuitry will pull
its quiescent current through its SW pin. This is ?ne if
your system can tolerate a few mA in this state. If you
ground the RUN/SS pin, the SW pin current will drop to
essentially zero. However, if the V IN pin is grounded while
the output is held high, then parasitic diodes inside the
LT3972 can pull large currents from the output through
the SW pin and the V IN pin. Figure 8 shows a circuit that
will run only when the input voltage is present and that
protects against a shorted or reversed input.
D4
MBRS340
The LT3972 will not enter Burst Mode operation at low
output loads while synchronized to an external clock, but
V IN
V IN
BOOST
LT3972
instead will skip pulses to maintain regulation.
RUN/SS
V C
SW
V OUT
The LT3972 may be synchronized over a 250kHz to 2MHz
range. The R T resistor should be chosen to set the LT3972
switching frequency 20% below the lowest synchronization
input. For example, if the synchronization signal will be
250kHz and higher, the R T should be chosen for 200kHz.
To assure reliable and safe operation, the LT3972 will only
synchronize when the output voltage is near regulation
as indicated by the PG ?ag. It is therefore necessary to
choose a large enough inductor value to supply the required
output current at the frequency set by the R T resistor. See
the Inductor Selection section. It is also important to note
that slope compensation is set by the R T value: When the
sync frequency is much higher than the one set by R T , the
slope compensation will be signi?cantly reduced which
may require a larger inductor value to prevent subharmonic
oscillation.
GND FB
BACKUP
3972 F08
Figure 8. Diode D4 Prevents a Shorted Input from
Discharging a Backup Battery Tied to the Output. It Also
Protects the Circuit from a Reversed Input. The LT3972
Runs Only When the Input is Present
PCB Layout
For proper operation and minimum EMI, care must be
taken during printed circuit board layout. Figure 9 shows
the recommended component placement with trace,
ground plane and via locations. Note that large, switched
currents ?ow in the LT3972’s V IN and SW pins, the catch
3972fa
16
相关PDF资料 |
PDF描述 |
|---|---|
| GSC31DREF-S13 | CONN EDGECARD 62POS .100 EXTEND |
| MAX6716AUTRHD2+T | IC SUPERVISOR MPU SOT23-6 |
| GMC31DREF-S13 | CONN EDGECARD 62POS .100 EXTEND |
| MAX6716AUTRVD1+T | IC SUPERVISOR MPU SOT23-6 |
| RBC60DCMH | CONN EDGECARD 120POS .100 WW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3972IDD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:33V, 3.5A, 2.4MHz Step-Down Switching Regulator with 75μA Quiescent Current |
| LT3972IMSE#PBF | 功能描述:IC REG BUCK ADJ 3.5A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3972IMSE#TRPBF | 功能描述:IC REG BUCK ADJ 3.5A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3972IMSEPBF | 制造商:Linear Technology 功能描述:DC-DC Converter Step-Down 3.6-33V MSOP10 |
| LT3972IMSE-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:33V, 3.5A, 2.4MHz Step-Down Switching Regulator with 75μA Quiescent Current |
发布紧急采购，3分钟左右您将得到回复。