- 您现在的位置：买卖IC网 > PDF目录14029 > LT3973EDD#TRPBF (Linear Technology)IC REG BUCK ADJ 0.75A 10DFN PDF资料下载
参数资料
| 型号： | LT3973EDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 0.75A 10DFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.21 V ~ 24 V |
| 输入电压： | 4.2 V ~ 42 V |
| PWM 型： | 电流模式，Burst Mode? |
| 频率 - 开关： | 195kHz ~ 2.15MHz |
| 电流 - 输出： | 750mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 10-DFN（3x3） |
LT3973/LT3973-3.3/LT3973-5
APPLICATIONS INFORMATION
V OUT + V D
V IN(MIN1) = – V D + V SW
V OUT + V D
f SW
about 97.5%. This leads to a minimum input voltage of
approximately:
DC MAX
where V OUT is the output voltage, V D is the catch diode
drop (~0.7V), V SW is the internal switch drop (~0.5V at
max load), and DC MAX is the maximum duty cycle.
The final factor affecting the minimum input voltage is the
minimum dropout voltage. When the OUT pin is tied to
V OUT , the LT3973 regulates the output such that it stays
more than 530mV below V IN . This enforced minimum
dropout voltage is due to reasons that are covered in a
later section. This places a limitation on the minimum
input voltage as follows:
V IN(MIN2) = V OUT + V DROPOUT(MIN)
where V OUT is the output voltage and V DROPOUT(MIN) is
the minimum dropout voltage (530mV).
Combining these factors leads to the overall minimum
input voltage:
V IN(MIN) = max(V IN(MIN1) , V IN(MIN2) , 4.2V)
Note that the LT3973 will begin switching at a lower input
voltage (typically 3V) but will regulate to a lower FB voltage
in this region of operation (see the Typical Performance
Characteristics section).
be reduced below the programmed frequency to prevent
damage to the part. The output voltage ripple and inductor
current ripple may also be higher than in typical operation,
however the output will still be in regulation.
Inductor Selection
For a given input and output voltage, the inductor value
and switching frequency will determine the ripple current.
The ripple current increases with higher V IN or V OUT and
decreases with higher inductance and faster switching
frequency. A good starting point for selecting the induc-
tor value is:
L = 1.5
where V D is the voltage drop of the catch diode (~0.7V),
L is in μH and f SW is in MHz. The inductor’s RMS current
rating must be greater than the maximum load current
and its saturation current should be about 30% higher.
For robust operation in fault conditions (start-up or short
circuit) and high input voltage (>30V), the saturation cur-
rent should be above 1.5A. To keep the efficiency high,
the series resistance (DCR) should be less than 0.1Ω, and
the core material should be intended for high frequency
applications. Table 2 lists several inductor vendors.
Table 2. Inductor Vendors
VENDOR URL
Coilcraft www.coilcraft.com
Maximum Input Voltage Range
The highest allowed V IN during normal operation (V IN(OP-
MAX) ) is limited by minimum duty cycle and can be calcu-
lated by the following equation:
Sumida
Toko
Würth Elektronik
Coiltronics
Murata
www.sumida.com
www.tokoam.com
www.we-online.com
www.cooperet.com
www.murata.com
V IN(OP-MAX) =
– V D + V SW
V OUT + V D
f SW ? t ON(MIN)
where t ON(MIN) is the minimum switch on time.
However, the circuit will tolerate inputs up to the absolute
maximum ratings of the V IN and BOOST pins, regardless of
chosen switching frequency. During such transients where
V IN is higher than V IN(OP-MAX) , the switching frequency will
This simple design guide will not always result in the
optimum inductor selection for a given application. As a
general rule, lower output voltages and higher switching
frequency will require smaller inductor values. If the ap-
plication requires less than 750mA load current, then a
lesser inductor value may be acceptable. This allows use
of a physically smaller inductor, or one with a lower DCR
resulting in higher efficiency. There are several graphs in
the Typical Performance Characteristics section of this data
3973fa
13
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6717AUKRDD1+T | IC SUPERVISOR MPU SOT23-5 |
| VI-JVX-CZ-F2 | CONVERTER MOD DC/DC 5.2V 25W |
| MAX6717AUKMSD6+T | IC SUPERVISOR MPU SOT23-5 |
| GSC36DREI | CONN EDGECARD 72POS .100 EYELET |
| MAX6717AUKRDD2+T | IC SUPERVISOR MPU SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3973EMSE#PBF | 功能描述:IC REG BUCK ADJ 0.75A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3973EMSE#TRPBF | 功能描述:IC REG BUCK ADJ 0.75A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3973EMSE-3.3#PBF | 功能描述:IC REG BUCK 3.3V 0.75A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3973EMSE-3.3#TRPBF | 功能描述:IC REG BUCK 3.3V 0.75A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3973EMSE-5#PBF | 功能描述:IC REG BUCK 5V 0.75A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
发布紧急采购，3分钟左右您将得到回复。