- 您现在的位置：买卖IC网 > PDF目录14029 > LT3973EDD#TRPBF (Linear Technology)IC REG BUCK ADJ 0.75A 10DFN PDF资料下载
参数资料
| 型号： | LT3973EDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 0.75A 10DFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.21 V ~ 24 V |
| 输入电压： | 4.2 V ~ 42 V |
| PWM 型： | 电流模式，Burst Mode? |
| 频率 - 开关： | 195kHz ~ 2.15MHz |
| 电流 - 输出： | 750mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 10-DFN（3x3） |
LT3973/LT3973-3.3/LT3973-5
APPLICATIONS INFORMATION
C OUT =
V IN = 24V
sheetthatshowthemaximumloadcurrentasafunction
of input voltage for several popular output voltages. Low
inductance may result in discontinuous mode operation,
which is acceptable but reduces maximum load current.
For details of maximum output current and discontinu-
ous mode operation, see Application Note 44. Finally, for
duty cycles greater than 50% (V OUT /V IN > 0.5), there is
a minimum inductance required to avoid subharmonic
oscillations. See Application Note 19.
Input Capacitor
Bypass the input of the LT3973 circuit with a ceramic capaci-
tor of X7R or X5R type. Y5V types have poor performance
over temperature and applied voltage, and should not be
used. A 4.7μF ceramic capacitor is adequate to bypass the
LT3973 and will easily handle the ripple current. Note that
larger input capacitance is required when a lower switching
frequency is used (due to longer on-times). If the input
power source has high impedance, or there is significant
inductance due to long wires or cables, additional bulk
capacitance may be necessary. This can be provided with
a low performance electrolytic capacitor.
Step-down regulators draw current from the input sup-
ply in pulses with very fast rise and fall times. The input
capacitor is required to reduce the resulting voltage
ripple at the LT3973 and to force this very high frequency
switching current into a tight local loop, minimizing EMI.
A 4.7μF capacitor is capable of this task, but only if it is
placed close to the LT3973 (see the PCB Layout section).
A second precaution regarding the ceramic input capacitor
concerns the maximum input voltage rating of the LT3973.
A ceramic input capacitor combined with trace or cable
inductance forms a high quality (under damped) tank
circuit. If the LT3973 circuit is plugged into a live supply,
the input voltage can ring to twice its nominal value, pos-
sibly exceeding the LT3973’s voltage rating. This situation
is easily avoided (see the Hot Plugging Safely section).
Output Capacitor and Output Ripple
The output capacitor has two essential functions. It stores
energy in order to satisfy transient loads and stabilize the
LT3973’s control loop. Ceramic capacitors have very low
equivalent series resistance (ESR) and provide the best
ripple performance. A good starting value is:
50
V OUT ? f SW
where f SW is in MHz and C OUT is the recommended output
capacitance in μF. Use X5R or X7R types. This choice will
provide low output ripple and good transient response.
Transient performance can be improved with a higher value
capacitor if combined with a phase lead capacitor (typically
15pF) between the output and the feedback pin. A lower
value of output capacitor can be used to save space and
cost but transient performance will suffer.
The second function is that the output capacitor, along
with the inductor, filters the square wave generated by the
LT3973 to produce the DC output. In this role it determines
the output ripple, so low impedance (at the switching
frequency) is important. The output ripple decreases with
increasing output capacitance, down to approximately
1mV. See Figure 1. Note that a larger phase lead capacitor
should be used with a large output capacitor.
16
FRONT PAGE APPLICATION
14
12
10
8
6
4 V IN = 12V
2
0
0 20 40 60 80 100
C OUT (μF)
3973 F01
Figure 1. Worst-Case Output Ripple Across Full Load Range
When choosing a capacitor, look carefully through the
data sheet to find out what the actual capacitance is under
operating conditions (applied voltage and temperature).
A physically larger capacitor or one with a higher voltage
rating may be required. Table 3 lists several capacitor
vendors.
3973fa
14
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6717AUKRDD1+T | IC SUPERVISOR MPU SOT23-5 |
| VI-JVX-CZ-F2 | CONVERTER MOD DC/DC 5.2V 25W |
| MAX6717AUKMSD6+T | IC SUPERVISOR MPU SOT23-5 |
| GSC36DREI | CONN EDGECARD 72POS .100 EYELET |
| MAX6717AUKRDD2+T | IC SUPERVISOR MPU SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3973EMSE#PBF | 功能描述:IC REG BUCK ADJ 0.75A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3973EMSE#TRPBF | 功能描述:IC REG BUCK ADJ 0.75A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3973EMSE-3.3#PBF | 功能描述:IC REG BUCK 3.3V 0.75A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3973EMSE-3.3#TRPBF | 功能描述:IC REG BUCK 3.3V 0.75A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3973EMSE-5#PBF | 功能描述:IC REG BUCK 5V 0.75A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
发布紧急采购，3分钟左右您将得到回复。