- 您现在的位置：买卖IC网 > PDF目录14819 > LT3991EMSE-5#PBF (Linear Technology)IC REG BUCK 5V 1.2A 10-MSOP PDF资料下载
参数资料
| 型号： | LT3991EMSE-5#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 5V 1.2A 10-MSOP |
| 标准包装： | 50 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 5V |
| 输入电压： | 4.3 V ~ 55 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 200kHz ~ 2MHz |
| 电流 - 输出： | 1.2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 10-MSOP 裸露焊盘 |
LT3991/LT3991-3.3/LT3991-5
APPLICATIONS INFORMATION
V OUT + V D
1 ? f SW t OFF(MIN)
f SW(MAX) =
V IN(OP-MAX) =
– V D + V SW
11
OperatingFrequencyTradeoffs
Selection of the operating frequency is a tradeoff between
efficiency, component size, minimum dropout voltage, and
maximum input voltage. The advantage of high frequency
operation is that smaller inductor and capacitor values may
be used. The disadvantages are lower efficiency, lower
maximum input voltage, and higher dropout voltage. The
highest acceptable switching frequency (f SW(MAX) ) for a
given application can be calculated as follows:
V OUT + V D
t ON(MIN) (V IN ? V SW + V D )
where V IN is the typical input voltage, V OUT is the output
voltage, V D is the catch diode drop (~0.5V), and V SW is
the internal switch drop (~0.5V at max load). This equation
shows that slower switching frequency is necessary to
safely accommodate high V IN /V OUT ratio. Also, as shown
in the Input Voltage Range section, lower frequency allows
a lower dropout voltage. The input voltage range depends
on the switching frequency because the LT3991 switch has
finite minimum on and off times. The minimum switch on
and off times are strong functions of temperature. Use
the typical minimum on and off curves to design for an
application’s maximum temperature, while adding about
30% for part-to-part variation. The minimum and maximum
duty cycles that can be achieved taking minimum on and
off times into account are:
DC MIN = f SW t ON(MIN)
DC MAX = 1 ? f SW t OFF(MIN)
wheref SW istheswitchingfrequency,thet ON(MIN) isthe
minimum switch on-time, and the t OFF(MIN) is the minimum
switch off-time. These equations show that duty cycle
range increases when switching frequency is decreased.
See the Electrical Characteristics section for t ON(MIN) and
t OFF(MIN) values.
A good choice of switching frequency should allow ad-
equate input voltage range (see Input Voltage Range sec-
tion) and keep the inductor and capacitor values small.
Input Voltage Range
The minimum input voltage is determined by either the
LT3991’s minimum operating voltage of 4.3V or by its
maximum duty cycle (see equation in Operating Frequency
Tradeoffs section). The minimum input voltage due to
duty cycle is:
V IN(MIN) = ? V D + V SW
where V IN(MIN) is the minimum input voltage, V OUT is
the output voltage, V D is the catch diode drop (~0.5V),
V SW is the internal switch drop (~0.5V at max load), f SW
is the switching frequency (set by R T ), and t OFF(MIN) is
the minimum switch off-time. Note that higher switch-
ing frequency will increase the minimum input voltage.
If a lower dropout voltage is desired, a lower switching
frequency should be used.
The maximum input voltage for LT3991 applications
depends on switching frequency, the Absolute Maximum
Ratings of the V IN and BOOST pins, and the operating
mode. For a given application where the switching fre-
quency and the output voltage are already selected, the
maximum input voltage (V IN(OP-MAX) ) that guarantees
optimum output voltage ripple for that application can be
found by applying the following equation:
V OUT + V D
f SW ? t ON(MIN)
where t ON(MIN) is the minimum switch on-time. Note that
a higher switching frequency will decrease the maximum
operating input voltage. Conversely, a lower switching
frequency will be necessary to achieve normal operation
at higher input voltages.
The circuit will tolerate inputs above the maximum op-
erating input voltage and up to the Absolute Maximum
Ratings of the V IN and BOOST pins, regardless of chosen
switching frequency. However, during such transients
where V IN is higher than V IN(OP-MAX) , the LT3991 will enter
pulse-skipping operation where some switching pulses are
skipped to maintain output regulation. The output voltage
ripple and inductor current ripple will be higher than in
typical operation. Do not overload when V IN is greater
than V IN(OP-MAX) .
3991fa
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JVN-EY-F3 | CONVERTER MOD DC/DC 18.5V 50W |
| LT3511EMS#PBF | IC REG FLYBACK ISOLATD 16-MSOP |
| LT3991EMSE-3.3#PBF | IC REG BUCK 3.3V 1.2A 10-MSOP |
| LT3509EDE#PBF | IC REG BUCK ADJ 0.7A DL 14DFN |
| VI-JVN-EY-F2 | CONVERTER MOD DC/DC 18.5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3991EMSEPBF | 制造商:Linear Technology 功能描述:DC-DC Converter Step-Down 4.3-55V MSOP10 |
| LT3991EMSETRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:55V, 1.2A Step-Down Regulator with 2.8 Quiescent Current |
| LT3991IDD#PBF | 功能描述:IC REG BUCK ADJ 1.2A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
| LT3991IDD#TRPBF | 功能描述:IC REG BUCK ADJ 1.2A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3991IDDPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:55V, 1.2A Step-Down Regulator with 2.8 Quiescent Current |
发布紧急采购，3分钟左右您将得到回复。