- 您现在的位置：买卖IC网 > PDF目录13968 > LT3991IMSE-5#PBF (Linear Technology)IC REG BUCK 5V 1.2A 10-MSOP PDF资料下载
参数资料
| 型号： | LT3991IMSE-5#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 12/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 5V 1.2A 10-MSOP |
| 标准包装： | 50 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 5V |
| 输入电压： | 4.3 V ~ 55 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 200kHz ~ 2MHz |
| 电流 - 输出： | 1.2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 10-MSOP 裸露焊盘 |
LT3991/LT3991-3.3/LT3991-5
APPLICATIONS INFORMATION
V OUT + V D
I OUT(MAX) = I LIM –
(1 ? DC) ? (V OUT + V D )
L ? f SW
InductorSelectionandMaximumOutputCurrent
A good first choice for the inductor value is:
L =
f SW
where f SW is the switching frequency in MHz, V OUT is the
output voltage, V D is the catch diode drop (~0.5V) and L
is the inductor value in μH.
The inductor’s RMS current rating must be greater than the
maximum load current and its saturation current should be
about 30% higher. For robust operation in fault conditions
(start-up or short-circuit) and high input voltage (>30V),
the saturation current should be above 2.8A. To keep the
efficiency high, the series resistance (DCR) should be less
than 0.1Ω, and the core material should be intended for
high frequency applications. Table 2 lists several vendors
and suitable types.
The inductor value must be sufficient to supply the desired
maximum output current (I OUT(MAX) ), which is a function
of the switch current limit (I LIM ) and the ripple current.
Δ I L
2
The LT3991 limits its peak switch current in order to protect
itself and the system from overload faults. The LT3991’s
switch current limit (I LIM ) is at least 2.33A at low duty
cycles and decreases linearly to 1.8A at DC = 0.8.
Table 2. Inductor Vendors
VENDOR URL PART SERIES TYPE
Murata www.murata.com LQH55D Open
TDK www.componenttdk.com SLF7045 Shielded
SLF10145 Shielded
Toko www.toko.com D62CB Shielded
D63CB Shielded
D73C Shielded
D75F Open
Coilcraft www.coilcraft.com MSS7341 Shielded
MSS1038 Shielded
Sumida www.sumida.com CR54 Open
CDRH74 Shielded
CDRH6D38 Shielded
CR75 Open
12
When the switch is off, the potential across the inductor
is the output voltage plus the catch diode drop. This gives
the peak-to-peak ripple current in the inductor:
Δ I L =
where f SW is the switching frequency of the LT3991, DC is
the duty cycle and L is the value of the inductor. Therefore,
the maximum output current that the LT3991 will deliver
depends on the switch current limit, the inductor value,
and the input and output voltages. The inductor value may
have to be increased if the inductor ripple current does
not allow sufficient maximum output current (I OUT(MAX) )
given the switching frequency, and maximum input voltage
used in the desired application.
The optimum inductor for a given application may differ
from the one indicated by this simple design guide. A larger
value inductor provides a higher maximum load current and
reduces the output voltage ripple. If your load is lower than
the maximum load current, than you can relax the value of
the inductor and operate with higher ripple current. This
allows you to use a physically smaller inductor, or one with
a lower DCR resulting in higher efficiency. Be aware that if
the inductance differs from the simple rule above, then the
maximum load current will depend on the input voltage. In
addition, low inductance may result in discontinuous mode
operation, which further reduces maximum load current.
For details of maximum output current and discontinuous
operation, see Linear Technology’s Application Note 44.
Finally, for duty cycles greater than 50% (V OUT /V IN >0.5),
a minimum inductance is required to avoid sub-harmonic
oscillations. See Application Note 19.
One approach to choosing the inductor is to start with
the simple rule given above, look at the available induc-
tors, and choose one to meet cost or space goals. Then
use the equations above to check that the LT3991 will be
able to deliver the required output current. Note again
that these equations assume that the inductor current is
continuous. Discontinuous operation occurs when I OUT
is less than Δ I L /2.
3991fa
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6307EUK44D3+T | IC SUPERVISOR 4.380V SOT23-5 |
| ABM12DRKF-S13 | CONN EDGECARD EXTEND 24POS .156 |
| MAX6307EUK46D3+T | IC SUPERVISOR 4.630V SOT23-5 |
| 35MS522MEFCTZ6.3X5 | CAP ALUM 22UF 35V 20% RADIAL |
| MAX6306EUK30D3+T | IC SUPERVISOR 3.00V SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3991IMSEPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:55V, 1.2A Step-Down Regulator with 2.8 Quiescent Current |
| LT3991IMSETRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:55V, 1.2A Step-Down Regulator with 2.8 Quiescent Current |
| LT3992 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic Dual Tracking |
| LT3992EFE#PBF | 功能描述:IC REG BUCK ADJ 3A DL 38-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3992EFE#TRPBF | 功能描述:IC REG BUCK ADJ 3A DL 38-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。