- 您现在的位置：买卖IC网 > PDF目录19877 > LT4250LIS8#TRPBF (Linear Technology)IC CONTRLR HOTSWAP NEG 48V 8SOIC PDF资料下载
参数资料
| 型号： | LT4250LIS8#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 5/14页 |
| 文件大小： | 236K |
| 描述： | IC CONTRLR HOTSWAP NEG 48V 8SOIC |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | -20 V ~ -80 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
LT4250L/LT4250H
5
4250lhfa
PIN FUNCTIONS
for this pin is 1.5約. Add an external capacitor to this pin
for additional filtering.
V
EE
(Pin 4): Negative Supply Voltage Input. Connect to
the lower potential of the power supply.
SENSE (Pin 5): Circuit Breaker Sense Pin. With a sense
resistor placed in the supply path between V
EE
and SENSE,
the overcurrent condition will pull down the GATE pin and
regulate the voltage across the resistor to be 50mV . If
the overcurrent condition exists for more than 500約 the
electronic circuit breaker will trip and turnoff the external
MOSFET .
If the current limit value is set to twice the normal operating
current, only 25mV is dropped across the sense resistor
during normal operation. To disable the current limit feature,
V
EE
and SENSE can be shorted together.
GATE (Pin 6): Gate Drive Output for the External N-channel
MOSFET . The GATE pin will go high when the following
start-up conditions are met: the UV pin is high, the OV pin
is low, (V
SENSE
V
EE
) < 50mV and the V
DD
pin is greater
than V
UVLOH
. The GATE pin is pulled high by a 45糀 cur-
rent source and pulled low with a 50mA current source.
During current limit the GATE pin is pulled low using a
100mA current source.
DRAIN (Pin 7): Analog Drain Sense Input. Connect this
pin to the drain of the external N-channel MOSFET and
the V
pin of the power module. When the DRAIN pin is
below V
DL
, the PWRGD/PWRGD pin will latch to indicate
the switch is on.
V
DD
(Pin 8): Positive Supply Voltage Input. Connect this
pin to the higher potential of the power supply inputs and
the V
+
pin of the power module. An undervoltage lockout
circuit disables the chip until the V
DD
pin is greater than
the 16V V
UVLOH
threshold.
PWRGD/PWRGD (Pin 1): Power Good Output Pin. This pin
will latch a power good indication when V
DRAIN
is within
V
DL
of V
EE
and V
GATE
is within V
GH
of 擵
GATE
. This pin
can be connected directly to the enable pin of a power
module.
When the DRAIN pin of the LT4250L is above V
EE
by more
than V
DL
or V
GATE
is more than V
GH
from 擵
GATE
, the
PWRGD pin will be high impedance, allowing the pull-up
current of the modules enable pin to pull the pin high and
turn the module off. When V
DRAIN
drops below V
DL
and
V
GATE
rises above V
GH
, the PWRGD pin sinks current to
V
EE
, pulling the enable pin low and turning on the module.
This condition is latched until the GATE pin is turned off
via the UV , OV , UVLO or the electronic circuit breaker.
When the DRAIN pin of the LT4250H is above V
EE
by more
than V
DL
or V
GATE
is more than V
GH
from 擵
GATE
, the
PWRGD pin will sink current to the DRAIN pin which pulls
the modules enable pin low, forcing it off. When V
DRAIN
drops below V
DL
and V
GATE
rises above V
GH
, the PWRGD
sink current is turned off, allowing the modules pull-up
current to pull the enable pin high and turn on the module.
This condition is latched until the GATE pin is turned off
via the UV , OV , UVLO or the electronic circuit breaker.
OV (Pin 2): Analog Overvoltage Input. When OV is pulled
above the 1.255V threshold, an overvoltage condition is
detected and the GATE pin will be immediately pulled low.
The GATE pin will remain low until OV drops below the
1.235V threshold.
UV (Pin 3): Analog Undervoltage Input. When UV is pulled
below the 1.125V threshold, an undervoltage condition
is detected and the GATE pin will be immediately pulled
low. The GATE pin will remain low until UV rises above
the 1.255 threshold.
The UV pin is also used to reset the electronic circuit
breaker. If the UV pin is cycled low and high following the
trip of the circuit breaker, the circuit breaker is reset and a
normal power-up sequence will occur. The response time
相关PDF资料 |
PDF描述 |
|---|---|
| XC1765ELVOG8C | IC 3V SER CFG PROM 65K 8-SOIC |
| MAX8510EXK25+T | IC REG LDO 2.5V .12A SC70-5 |
| HBC06DRTI-S13 | CONN EDGECARD 12POS .100 EXTEND |
| R-786.5-0.5 | CONV DC/DC .5A 6.5V OUT SIP VERT |
| XC1701LPD8C | IC 1 MB 3.3V SER CONF PROM 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT4254 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Positive High Voltage Hot Swap Controller with Open-Circuit Detect |
| LT4254CGN | 功能描述:IC CTRLR HOTSWAP POSVOLT 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LT4254CGN#PBF | 功能描述:IC CTRLR HOTSWAP POSVOLT 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LT4254CGN#TR | 功能描述:IC CTLR HOTSWAP POS 16-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LT4254CGN#TRPBF | 功能描述:IC CTRLR HOTSWAP POSVOLT 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。