参数资料
型号: LT6555CGN#PBF
厂商: Linear Technology
文件页数: 16/16页
文件大小: 0K
描述: IC VIDEO MULTIPLEXER 2X1 24SSOP
标准包装: 55
功能: 视频多路复用器
电路: 3 x 2:1
电压电源: 双电源
电压 - 电源,单路/双路(±): ±2.25 V ~ 6 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 24-SSOP(0.154",3.90mm 宽)
供应商设备封装: 24-SSOP
包装: 管件
产品目录页面: 1321 (CN2011-ZH PDF)
LT6555
9
6555f
APPLICATIO S I FOR ATIO
WU
UU
VREF voltage to the desired level. The only way to cover the
full common mode voltage range of V+ 1V to V+ – 1V is
to shift VREF up or down. Note that on a single supply, the
unclamped input range limits the output low swing to 2V
(1V multiplied by the internal gain of 2).
The VREF pin can also be directly driven with a DC source.
Bypassing the VREF pin is not necessary.
The inputs can be driven beyond the point at which the
output clips so long as input currents are limited to less
than
±10mA. Continuing to drive the input beyond the
output limit can result in increased current drive and
slightly increased swing, but will also increase supply
current and may result in delays in transient response at
larger levels of overdrive.
Layout and Grounding
It is imperative that care is taken in PCB layout in order to
benefit from the very high speed and very low crosstalk of
the LT6555. Separate power and ground planes are highly
recommended and trace lengths should be kept as short
as possible. If input or output traces must be run over a
distance of several centimeters, they should use a con-
trolled impedance with matching series and shunt resis-
tances (nominally 75
) to maintain signal fidelity.
Series termination resistors should be placed as close to
the output pins as possible to minimize output capaci-
tance. See the Typical Performance Characteristics sec-
tion for a plot of frequency response with various output
capacitors—only 10pF of parasitic output capacitance
before the series termination resistor causes 6dB of
peaking in the frequency response!
Low ESL/ESR bypass capacitors should be placed as
close to the positive and negative supply pins as possible.
One 4700pF ceramic capacitor is recommended for both
V+ and Vsupply busses. Additional 470pF ceramic ca-
pacitors with minimal trace length on each supply pin will
further improve AC and transient response as well as
channel isolation. For high current drive and large-signal
transient applications, additional 1
F to 10F tantalums
should be added on each supply. The smallest value
capacitors should be placed closest to the package.
If the AGND pins are not connected to ground, they must
be carefully bypassed to maintain minimal impedance
over frequency. Although crosstalk will vary depending
upon board layout, a recommended starting point for
bypass capacitors would be 470pF as close as possible to
each AGND pin with a single 4700pF capacitor in parallel.
VREF
40k
6555 F01
V+
V
IN
Figure 1. Simplified Schematic of VREF Pin and Input Clamping
相关PDF资料
PDF描述
ADG453BRZ IC SWITCH QUAD SPST 16SOIC
PIC16LC622A-04I/SO IC MCU OTP 2KX14 COMP 18SOIC
ADG608BNZ IC MULTIPLEXER 8X1 16DIP
VE-B61-CU-F4 CONVERTER MOD DC/DC 12V 200W
LTC201ACS#PBF IC SWITCH QUAD SPST 16SOIC
相关代理商/技术参数
参数描述
LT6555CUF 制造商:LINER 制造商全称:Linear Technology 功能描述:650MHz Gain of 2 Triple 2:1Video Multiplexer
LT6555CUF#PBF 功能描述:IC VIDEO MULTIPLEXER 2X1 24QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关,多路复用器,多路分解器 系列:- 其它有关文件:STG4159 View All Specifications 标准包装:5,000 系列:- 功能:开关 电路:1 x SPDT 导通状态电阻:300 毫欧 电压电源:双电源 电压 - 电源,单路/双路(±):±1.65 V ~ 4.8 V 电流 - 电源:50nA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:7-WFBGA,FCBGA 供应商设备封装:7-覆晶 包装:带卷 (TR)
LT6555CUF#TRPBF 功能描述:IC VIDEO MULTIPLEXER 2X1 24QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关,多路复用器,多路分解器 系列:- 其它有关文件:STG4159 View All Specifications 标准包装:5,000 系列:- 功能:开关 电路:1 x SPDT 导通状态电阻:300 毫欧 电压电源:双电源 电压 - 电源,单路/双路(±):±1.65 V ~ 4.8 V 电流 - 电源:50nA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:7-WFBGA,FCBGA 供应商设备封装:7-覆晶 包装:带卷 (TR)
LT6555IGN 制造商:Linear Technology 功能描述:Video Multiplexer 24-Pin SSOP N
LT6555IGN#PBF 功能描述:IC VIDEO MULTIPLEXER 2X1 24SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关,多路复用器,多路分解器 系列:- 其它有关文件:STG4159 View All Specifications 标准包装:5,000 系列:- 功能:开关 电路:1 x SPDT 导通状态电阻:300 毫欧 电压电源:双电源 电压 - 电源,单路/双路(±):±1.65 V ~ 4.8 V 电流 - 电源:50nA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:7-WFBGA,FCBGA 供应商设备封装:7-覆晶 包装:带卷 (TR)