参数资料
| 型号： | LT6600IS8-10 |
| 厂商： | Linear Technology |
| 文件页数： | 2/16页 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF 10MHZ LP FLTR 8-SOIC |
| 标准包装： | 100 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 输出类型： | 差分 |
| 电流 - 输入偏压： | 40µA |
| 电压 - 输入偏移： | 8000µV |
| 电流 - 电源： | 36mA |
| 电压 - 电源，单路/双路(±)： | 3 V ~ 11 V，±1.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 管件 |
LT6600-10
10
66001fe
APPLICATIONS INFORMATION
Figure 5, present the output of the LT6600-10 with a 1600Ω
differential load, or the equivalent of 800Ω to ground at
each output. The impedance seen by the network analyzer
input is still 50Ω, reducing reections in the cabling be-
tween the transformer and analyzer input.
voltage of VMID. While the internal 11k resistors are well
matched, their absolute value can vary by ±20%. This
should be taken into consideration when connecting an
external resistor network to alter the voltage of VMID.
Figure 5. (S8 Pin Numbers)
–
+
0.1μF
2.5V
–2.5V
–
+
LT6600-10
3
4
1
7
2
8
5
6
6600 F05
402Ω
NETWORK
ANALYZER
INPUT
50Ω
COILCRAFT
TTWB-16A
4:1
NETWORK
ANALYZER
SOURCE
COILCRAFT
TTWB-1010
1:1
50Ω
53.6Ω
388Ω
Figure 6
1MHz INPUT LEVEL (VP-P)
0
20
0
–20
–40
–60
–80
–100
–120
35
6600 F06
12
46
OUTPUT
LEVEL
(dBV)
3RD HARMONIC
85°C
1dB PASSBAND GAIN
COMPRESSION POINTS
1MHz 25°C
1MHz 85°C
3RD HARMONIC
25°C
2ND HARMONIC
25°C
2ND HARMONIC
85°C
Differential and Common Mode Voltage Ranges
The differential ampliers inside the LT6600-10 contain
circuitry to limit the maximum peak-to-peak differential
voltage through the lter. This limiting function prevents
excessive power dissipation in the internal circuitry
and provides output short-circuit protection. The limiting
function begins to take effect at output signal levels above
2VP-P and it becomes noticeable above 3.5VP-P. This is
illustrated in Figure 6; the LTC6600-10 was congured with
unity passband gain and the input of the lter was driven
with a 1MHz signal. Because this voltage limiting takes
place well before the output stage of the lter reaches the
supply rails, the input/output behavior of the IC shown
in Figure 6 is relatively independent of the power supply
voltage.
The two ampliers inside the LT6600-10 have independent
control of their output common mode voltage (see the
Block Diagram section). The following guidelines will
optimize the performance of the lter for single-supply
operation.
VMID must be bypassed to an AC ground with a 0.01μF or
higher capacitor. VMID can be driven from a low impedance
source, provided it remains at least 1.5V above V– and at
least 1.5V below V+. An internal resistor divider sets the
VOCM can be shorted to VMID for simplicity. If a different
common mode output voltage is required, connect VOCM
to a voltage source or resistor network. For 3V and 3.3V
supplies the voltage at VOCM must be less than or equal to
the mid-supply level. For example, voltage (VOCM) ≤1.65V
on a single 3.3V supply. For power supply voltages higher
than 3.3V the voltage at VOCM can be set above mid-supply.
The voltage on VOCM should not be more than 1V below
the voltage on VMID. The voltage on VOCM should not be
more than 2V above the voltage on VMID. VOCM is a high
impedance input.
The LT6600-10 was designed to process a variety of input
signals including signals centered around the mid-supply
voltage and signals that swing between ground and a
positive voltage in a single-supply system (Figure 1).
The range of allowable input common mode voltage (the
average of VIN+ and VIN– in Figure 1) is determined by
the power supply level and gain setting (see the Electrical
Characteristics section).
Common Mode DC Currents
In applications like Figure 1 and Figure 3 where the
LT6600-10 not only provides lowpass ltering but also level
shifts the common mode voltage of the input signal, DC
相关PDF资料 |
PDF描述 |
|---|---|
| LT6600IS8-2.5#PBF | IC AMP DIFF LP FLTR 2.5MHZ 8SOIC |
| LT6600IS8-20 | IC AMP DIFF LP FLTR 20MHZ 8-SOIC |
| LT6604IUFF-2.5#TRPBF | IC AMP DIFF LN DUAL 34-QFN |
| LT6604IUFF-5#TRPBF | IC AMP DIFF LN DUAL 34-QFN |
| LTC1047CSW#TRPBF | IC OPAMP CHOP-STBL W/CAP 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT6600IS8-10#PBF | 功能描述:IC AMP DIFF LP FLTR 10MHZ 8-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:45nA 电压 - 输入偏移:2000µV 电流 - 电源:1.4mA 电流 - 输出 / 通道:40mA 电压 - 电源，单路/双路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) 其它名称:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| LT6600IS8-10#TR | 功能描述:IC AMP DIFF FILTER 2.5MHZ 8SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源，单路/双路(±):2 V ~ 44 V，±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP（5x3） 包装:管件 |
| LT6600IS8-10#TRPBF | 功能描述:IC AMP DIFF LP FLTR 10MHZ 8-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:73 系列:Over-The-Top® 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.07 V/µs 增益带宽积:200kHz -3db带宽:- 电流 - 输入偏压:1nA 电压 - 输入偏移:285µV 电流 - 电源:50µA 电流 - 输出 / 通道:25mA 电压 - 电源，单路/双路(±):2 V ~ 44 V，±1 V ~ 22 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WFDFN 裸露焊盘 供应商设备封装:16-DFN-EP（5x3） 包装:管件 |
| LT6600IS8-15 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Very Low Noise, Differential Amplifi er and 15MHz Lowpass Filter |
| LT6600IS8-15#PBF | 功能描述:IC AMP DIFF LP FLTR 15MHZ 8-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
发布紧急采购，3分钟左右您将得到回复。