- 您现在的位置：买卖IC网 > PDF目录15253 > LTC1159IS-5#TRPBF (Linear Technology)IC REG CTRLR BUCK PWM CM 16-SOIC PDF资料下载
参数资料
| 型号： | LTC1159IS-5#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16-SOIC |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 250kHz |
| 占空比： | 100% |
| 电源电压： | 4 V ~ 40 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
LTC1159
LTC1159-3.3/LTC1159-5
OPERATIO
(Refer to Functional Diagram)
R SENSE = m ?
increases,theoutputvoltagedecreasesslightly.Thiscauses
the output of the gain stage to increase the current com-
parator threshold, thus tracking the load current.
The sequence of events for Burst Mode operation is very
similar to continuous operation with the cycle interrupted
by the voltage comparator. When the output voltage is at or
above the desired regulated value, the P-channel MOSFET
is held off by comparator V and the timing capacitor con-
tinues to discharge below V TH1 . When the timing capacitor
discharges past V TH2 , voltage comparator S trips, causing
the internal SLEEP line to go low and the N-channel MOSFET
to turn off.
The circuit now enters sleep mode with both power
MOSFETs turned off. In sleep mode, much of the circuitry
APPLICATIO S I FOR ATIO
The LTC1159 Compared to the LTC1148/LTC1149
Families
The LTC1159 family is closest in operation to the LTC1149
and shares much of the applications information. In addi-
tion to reduced quiescent and shutdown currents, the
LTC1159 adds an internal switch which allows the driver
and control sections to be powered from an external
source for higher efficiency. This change affects Power
MOSFET Selection, EXTV CC Pin Connection, Important
Information About LTC1159 Adjustable Applications, and
Efficiency Considerations found in this section.
The basic LTC1159 application circuit shown in Figure 1
is limited to a maximum input voltage of 30V due to
MOSFET breakdown. If the application does not require
greater than 18V operation, then the LTC1148 or
LTC1148HV should be used. For higher input voltages
where quiescent and shutdown current are not critical, the
LTC1149 may be a better choice since it is set up to drive
standard threshold MOSFETs.
R SENSE Selection for Output Current
R SENSE is chosen based on the required output current. The
LTC1159 current comparator has a threshold range that
is turned off, dropping the supply current from several
milliamps (with the MOSFETs switching) to 300 μ A. When
the output capacitor has discharged by the amount of
hysteresis in comparator V, the P-channel MOSFET is
again turned on and this process repeats. To avoid the
operation of the current loop interfering with Burst Mode
operation, a built-in offset is incorporated in the gain stage.
To prevent both the external MOSFETs from being turned
on at the same time, feedback is incorporated to sense the
state of the driver output pins. Before the N-gate output can
go high, the P-drive output must also be high. Likewise, the
P-drive output is prevented from going low when the
N-gate output is high.
of 0.15V/R SENSE . The current comparator threshold sets
the peak of the inductor ripple current, yielding a maximum
output current I MAX equal to the peak value less half the
peak-to-peak ripple current. For proper Burst Mode opera-
tion, I RIPPLE(P-P) must be less than or equal to the minimum
current comparator threshold.
Since efficiency generally increases with ripple current,
the maximum allowable ripple current is assumed, i.e.,
I RIPPLE(P-P) = 0.025V/R SENSE (see C T and L Selection for
Operating Frequency). Solving for R SENSE and allowing
a margin for variations in the LTC1159 and external
component values yields:
100
I MAX
A graph for selecting R SENSE versus maximum output
current is given in Figure 2. The LTC1159 series works well
with values of R SENSE from 0.02 ? to 0.2 ? .
The load current below which Burst Mode operation com-
mences, I BURST , and the peak short-circuit current, I SC(PK) ,
both track I MAX . Once R SENSE has been chosen, I BURST and
I SC(PK) can be predicted from the following equations:
extends from a minimum of 0.025V/R SENSE to a maximum
7
相关PDF资料 |
PDF描述 |
|---|---|
| RGM15DRMN-S288 | CONN EDGECARD 30POS .156 EXTEND |
| 9250A-822-RC | CHOKE RF MOLDED 8.2UH IRON |
| RSM15DRMH-S288 | CONN EDGECARD 30POS .156 EXTEND |
| LTC1775IS#TRPBF | IC REG CTRLR BUCK PWM CM 16-SOIC |
| RMM15DRMH-S288 | CONN EDGECARD 30POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1160CN | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Interface IC |
| LTC1160CS | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Interface IC |
| LTC1160IN | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Interface IC |
| LTC1160IS | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Interface IC |
| LTC1162CN | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Interface IC |
发布紧急采购，3分钟左右您将得到回复。