- 您现在的位置：买卖IC网 > PDF目录80088 > LTC1266CS#TR-5 (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO16 PDF资料下载
参数资料
| 型号： | LTC1266CS#TR-5 |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | 0.150 INCH, PLASTIC, SO-16 |
| 文件页数： | 6/20页 |
| 文件大小： | 245K |
| 代理商： | LTC1266CS#TR-5 |
14
LTC1266
LTC1266-3.3/LTC1266-5
15nC. This results in IGATECHG = 6mA in 200kHz continu-
ous operation for a 2% to 3% typical mid-current loss with
VIN = 5V.
Note that the gate charge loss increases directly with
both input voltage and operating frequency. This is the
principal reason why the highest efficiency circuits oper-
ate at moderate frequencies. Furthermore, it argues against
using larger MOSFETs than necessary to control I
2R
losses, since overkill can cost efficiency as well as money!
3. I
2R losses are easily predicted from the DC resistances
of the MOSFET, inductor and current shunt. In continuous
mode the average output current flows through L and
RSENSE, but is “chopped” between the topside and bot-
tom-side MOSFETs. If the two MOSFETs have approxi-
mately the same RDS(ON), then the resistance of one
MOSFET can simply be summed with the resistances of L
and RSENSE to obtain I2R losses. For example, if each
RDS(ON) = 0.05, RL = 0.05 and RSENSE = 0.02, then
the total resistance is 0.12
.Thisresultsinlossesranging
from 3.5% to 15% as the output current increases from 1A
to 5A. I2R losses cause the efficiency to roll off at high
output currents.
Figure 8 shows how the efficiency losses in a typical
LTC1266 series regulator end up being apportioned. The
gate charge loss is responsible for the majority of the
efficiency lost in the mid-current region. If Burst Mode
operation was not employed at low currents, the gate
charge loss alone would cause efficiency to drop to
unacceptable levels (see Figure 7). With Burst Mode
discharge COUT until the regulator loop adapts to the
current change and returns VOUT to its steady-state value.
During this recovery time VOUT can be monitored for
overshoot or ringing which would indicate a stability
problem. The Pin 7 external components shown in the
Figure 1 circuit will prove adequate compensation for
most applications.
Efficiency Considerations
The percent efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Percent efficiency can be
expressed as:
% Efficiency = 100% – (L1 + L2 + L3 + ...)
where L1, L2, etc., are the individual losses as a percent-
age of input power. (For high efficiency circuits, only small
errors are incurred by expressing losses as a percentage
of output power).
Although all dissipative elements in the circuit produce
losses, three main sources usually account for most of the
losses in LTC1266 series circuits: 1) LTC1266 DC bias
current, 2) MOSFET gate charge current and 3) I
2R losses.
1. The DC supply current is the current which flows into
VIN (Pin 2). For VIN = 10V the LTC1266 DC supply current
is 170
A for no load, and increases proportionally with
load up to a constant 2.1mA after the LTC1266 series has
entered continuous mode. Because the DC bias current is
drawn from VIN, the resulting loss increases with input
voltage. For VIN = 5V the DC bias losses are generally less
than 1% for load currents over 30mA. However, at very
low load currents the DC bias current accounts for nearly
all of the loss.
2. MOSFET gate charge current results from switching the
gate capacitance of the power MOSFETs. Each time a
MOSFET gate is switched from low to high to low again, a
packet of charge dQ moves from Power VIN to ground. The
resulting dQ/dt is a current flowing into Power VIN (Pin 5)
which is typically much larger than the DC supply current.
In continuous mode, IGATECHG = f (QN + QP). The typical
gate charge for a 0.05
N-channel power MOSFET is
Figure 8. Efficiency Loss
IOUT (A)
0.01
EFFICIENCY/LOSS
(%)
90
95
1
1266 F08
85
80
0.03
0.1
0.3
5
100
GATE CHARGE
LTC1266 IQ
I2R
APPLICATIO S I FOR ATIO
WU
UU
相关PDF资料 |
PDF描述 |
|---|---|
| LM1301-7ERV2AH | 1-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
| LM1301-9RV3 | 1-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
| LM1501-7ERV2F | 1-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
| LM1601-7EPV2H | 1-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
| LM1601-9EPV0HF | 1-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1266IS | 功能描述:IC REG CTRLR BST PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1266IS#PBF | 功能描述:IC REG CTRLR BST PWM CM 16-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1266IS#TR | 功能描述:IC REG CTRLR BST PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1266IS#TRPBF | 功能描述:IC REG CTRLR BST PWM CM 16-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1266IS-3.3 | 功能描述:IC REG CTRLR BST PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。