- 您现在的位置：买卖IC网 > PDF目录1934 > LTC1343IGW#TRPBF (Linear Technology)IC TXRX SOFTWARE-SELECTBL 44SSOP PDF资料下载
参数资料
| 型号： | LTC1343IGW#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 2/28页 |
| 文件大小： | 0K |
| 描述： | IC TXRX SOFTWARE-SELECTBL 44SSOP |
| 标准包装： | 1,000 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 4/4 |
| 规程： | 多协议 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-BSOP（0.295"，7.50mm 宽） |
| 供应商设备封装： | 44-SSOP |
| 包装： | 带卷 (TR) |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
10
LTC1343
APPLICATIONS INFORMATION
WU
U
will configure the port for DCE mode when high, and DTE
when low.
The interface protocol may be selected simply by plugging
the appropriate interface cable into the connector. The
mode pins are routed to the connector and are left uncon-
nected (1) or wired to ground (0) in the cable as shown in
Figure 11.
The pull-up resistors R1 through R4 will ensure a binary
1 when a pin is left unconnected and that the two LTC1343s
and the LTC1344 enter the no-cable mode when the cable
is removed. In the no-cable mode the LTC1343 supply
current drops to less than 200
A and all LTC1343 driver
outputs and LTC1344 resistive terminations are forced
into a high impedance state. Note that the data latch pin,
LATCH, is shorted to ground for all chips.
The interface protocol may also be selected by the serial
controller or host microprocessor as shown in Figure 12.
The mode selection pins M0, M1, M2 and DCE/DTE can be
shared between multiple interface ports, while each port
Figure 11: Single Port DCE/V.35 Mode Selection in the Cable
RL (Remote Loop-back) and RI (Ring Indicate). The
LTC1344 cable termination chip is used only for the clock
and data signals because they must support V.35 cable
termination. The control signals do not need any external
resistors.
Mode Selection
The interface protocol is selected using the mode select
pins M0, M1, M2 and CTRL/CLK (see the Mode Selection
table). The CTRL/CLK pin should be pulled high if the
LTC1343 is being used to generate control signals and
pulled low if used to generate clock and data signals.
For example, if the port is configured as a V.35 interface,
the mode selection pins should be M2 = 1, M1 = 0, M0 = 0.
For the control signals, CTRL/CLK = 1 and the drivers and
receivers will operate in RS232 (V.28) electrical mode. For
the clock and data signals, CTRL/CLK = 0 and the drivers
and receivers will operate in V.35 electrical mode, except
for the single-ended driver and receiver which will operate
in the RS232 (V.28) electrical mode. The DCE/DTE pin
NC
CABLE
1343 F11
17
18
19
21
LTC1343
CONNECTOR
20
21
19
18
17
22
21
M2
M1
LTC1344
LATCH
M0 (DATA)
23
24
1
CTRL/CLK
22
(DATA)
M0
M1
M2
DCE/DTE
LATCH
20
CTRL/CLK
22
DCE/DTE
M2
M1
M0
(DATA)
LATCH
VCC
DCE/
DTE
R1, 10k
VCC
R2, 10k
VCC
R3, 10k
VCC
R4, 10k
VCC
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1344AIG#TRPBF | IC CABLE TERM MULTIPROTCL 24SSOP |
| LTC1344CG | IC CABLE TERM MULTIPROTCL 24SSOP |
| LTC1345ISW#TRPBF | IC TXRX V.35 SINGL SUPPLY 28SOIC |
| LTC1346ACSW#TRPBF | IC TXRX V.35 DCE/DTE 24-SOIC |
| LTC1347CSW#TRPBF | IC TXRX 5V RS232 LOW PWR 28-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1344ACG | 功能描述:IC CABLE TERM MULTIPROTCL 24SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 信号终端器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:SCSI，SE 端子数:9 电源电压:4 V ~ 5.25 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:管件 |
| LTC1344ACG#PBF | 功能描述:IC CABLE TERM MULTIPROTCL 24SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 信号终端器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:SCSI，SE 端子数:9 电源电压:4 V ~ 5.25 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:管件 |
| LTC1344ACG#TR | 功能描述:IC TERMINATOR CABLE MULTI 24SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 信号终端器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:SCSI，SE 端子数:9 电源电压:4 V ~ 5.25 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:管件 |
| LTC1344ACG#TRPBF | 功能描述:IC CABLE TERM MULTIPROTCL 24SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 信号终端器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:SCSI，SE 端子数:9 电源电压:4 V ~ 5.25 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:管件 |
| LTC1344AIG | 功能描述:IC TERMINATOR CABLE MULTI 24SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 信号终端器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:SCSI，SE 端子数:9 电源电压:4 V ~ 5.25 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。