- 您现在的位置：买卖IC网 > PDF目录10676 > LTC1404CS8#PBF (Linear Technology)IC A/D CONV 12BIT W/SHTDN 8-SOIC PDF资料下载
参数资料
| 型号： | LTC1404CS8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 4/24页 |
| 文件大小： | 0K |
| 描述： | IC A/D CONV 12BIT W/SHTDN 8-SOIC |
| 标准包装： | 100 |
| 位数： | 12 |
| 采样率（每秒）： | 600k |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 160mW |
| 电压电源： | 双 ± |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
| 输入数目和类型： | 1 个单端，单极；1 个单端，双极 |
| 产品目录页面： | 1346 (CN2011-ZH PDF) |
12
LTC1404
1404fa
APPLICATIONS INFORMATION
WU
U
If two pure sine waves of frequencies fa and fb are applied
to the ADC input, nonlinearities in the ADC transfer func-
tion can create distortion products at sum and difference
frequencies of mfa
± nfb, where m and n = 0, 1, 2, 3, etc.
For example, the 2nd order IMD terms include (fa + fb) and
(fa – fb) while the 3rd order IMD terms includes (2fa + fb),
(2fa – fb), (fa + 2fb) and (fa – 2fb). If the two input sine
waves are equal in magnitude, the value (in decibels) of the
2nd order IMD products can be expressed by the following
formula.
IMD fa
fb
fa
fb
±
() =
±
20log
Amplitude at (
)
Amplitude at fa
Figure 5 shows the IMD performance at a 100kHz input.
Figure 5. Intermodulation Distortion Plot in Bipolar Mode
FREQUENCY (kHz)
0
40
80
100
140
180
20
60
120
160
220
200
240 260 280 300
AMPLITUDE
(dB)
1404 F05
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
fSAMPLE = 600kHz
fa = 99.16992188kHz
fb = 102.6855469kHz
fa
fb
3fa
2fb – fa
2fa – fb
2fa + fb
2fa
3fb
fa + fb
2fb
2fb + fa
Peak Harmonic or Spurious Noise
The peak harmonic or spurious noise is the largest spec-
tral component excluding the input signal and DC. This
value is expressed in decibels relative to the RMS value of
a full-scale input signal.
Full Power and Full Linear Bandwidth
The full power bandwidth is the input frequency at which
the amplitude of the reconstructed fundamental is re-
duced by 3dB for a full-scale input signal.
The full linear bandwidth is the input frequency at which
the S/(N + D) has dropped to 68dB (11 effective bits). The
LTC1404 has been designed to optimize input bandwidth,
allowing the ADC to undersample input signals with fre-
quencies above the converter’s Nyquist Frequency. The
noise floor stays very low at high frequencies; S/(N + D)
becomes dominated by distortion at frequencies far be-
yond Nyquist.
Driving the Analog Input
The analog input of the LTC1404 is easy to drive. It draws
only one small current spike while charging the sample-
and-hold capacitor at the end of a conversion. During
conversion, the analog input draws only a small leakage
current. The only requirement is that the amplifier driving
the analog input must settle after the small current spike
before the next conversion starts. Any op amp that settles
in 160ns to small load current transient will allow maxi-
mum speed operation. If a slower op amp is used, more
settling time can be provided by increasing the time
between conversions. Suitable devices capable of driving
the ADC’s AIN input include the LT
1360 and the LT1363
op amps.
The LTC1404 comes with a built-in unipolar/bipolar detec-
tion circuit. If the VSS potential is forced below GND, the
internal circuitry will automatically switch to bipolar mode.
The following list is a summary of the op amps that are
suitable for driving the LTC1404, more detailed informa-
tion is available in the Linear Technology databooks or the
Linear Technology Web site.
LT 1215/LT1216: Dual and quad 23MHz, 50V/
s single
supply op amps. Single 5V to
±15V supplies, 6.6mA
specifications, 90ns settling to 0.5LSB.
LT1223: 100MHz video current feedback amplifier.
±5V
to
±15V supplies, 6mA supply current. Low distortion up
to and above 600kHz. Low noise. Good for AC applica-
tions.
LT1227: 140MHz video current feedback amplifier.
±5V
to
±15V supplies, 10mA supply current. Lowest distor-
tion at frequencies above 600kHz. Low noise. Best for AC
applications.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-2TP-IX-B1 | CONVERTER MOD DC/DC 13.8V 75W |
| AS1973-T | IC COMPARATOR DUAL O-D 8-MSOP |
| VI-JWH-MY-F3 | CONVERTER MOD DC/DC 52V 50W |
| AD7793BRUZ | IC ADC 24BIT SIG-DEL 3CH 16TSSOP |
| VI-BWF-MY-B1 | CONVERTER MOD DC/DC 72V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1404IS8 | 功能描述:IC A/D CONV 12BIT W/SHTDN 8-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC1404IS8#PBF | 功能描述:IC A/D CONV 12BIT W/SHTDN 8-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC1404IS8#TR | 功能描述:IC ADC 12BIT 600KSPS SHTDN 8SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC1404IS8#TRPBF | 功能描述:IC A/D CONV 12BIT W/SHTDN 8-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC1405CGN | 功能描述:IC ADC 12BIT 5MSPS SAMPLE 28SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。