- 您现在的位置：买卖IC网 > PDF目录2003 > LTC1420IGN#TRPBF (Linear Technology)IC ADC 12BIT 10MSPS SAMPL 28SSOP PDF资料下载
参数资料
| 型号： | LTC1420IGN#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 3/20页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 10MSPS SAMPL 28SSOP |
| 标准包装： | 2,500 |
| 位数： | 12 |
| 采样率（每秒）： | 10M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 300mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 2 个单端，双极；1 个差分，双极 |
11
LTC1420
1420fa
1420 F08a
+AIN
VSS
VIN
470pF
15
MINI CIRCUITS
T1-1T
1F
LTC1420
5V
–AIN
VCM
1420 F08b
+AIN
VSS
VIN
MINI CIRCUITS
T1-1T
1F
LTC1420
5V
–5V
–AIN
VCM
470pF
15
Figure 8a. Single Supply Transformer Coupled Input
Figure 8b. Dual Supply Transformer Coupled Input
+AIN
VIN
LTC1420
–AIN
470pF
30
Figure 9. RC Input Filter
APPLICATIONS INFORMATION
WU
U
Differential Operation
The THD and SFDR performance of the LTC1420 can be
improved by using a center tap RF transformer to drive the
inputs differentially. Though the signal can no longer be
DC coupled, the improvement in dynamic performance
makes this an attractive solution for some applications.
Typical connections for single and dual supply systems
are shown in Figures 8a and 8b. Good choices for trans-
formers are the Mini Circuits T1-1T (1:1 turns ratio) and
T4-6T (1:4 turns ratio). For best results, the transformer
should be located close to the LTC1420 on the printed
circuit board.
Choosing an Input Amplifier
Choosing an input amplifier is easy if a few requirements
are taken into consideration. First, to limit the magnitude
of the voltage spike seen by the amplifier from charging
the sampling capacitor, choose an amplifier that has a low
output impedance (<100) at the closed-loop bandwidth
frequency. For example, if an amplifier is used in a gain of
1 and has a unity-gain bandwidth of 100MHz, then the
output impedance at 100MHz must be less than 100.
The second requirement is that the closed-loop bandwidth
must be greater than 100MHz to ensure adequate small-
signal settling for full throughput rate. If slower op amps
are used, more settling time can be provided by increasing
the time between conversions.
The best choice for an op amp to drive the LTC1420 will
depend on the application. Generally applications fall into
two categories: AC applications where dynamic specifica-
tions are most critical and time domain applications where
DC accuracy and settling time are most critical.
Input Filtering
The noise and the distortion of the input amplifier and
other circuitry must be considered since they will add to
the LTC1420 noise and distortion. The small-signal band-
width of the sample-and-hold circuit is 100MHz. Any noise
or distortion products that are present at the analog inputs
will be summed over this entire bandwidth. Noisy input
circuitry should be filtered prior to the analog inputs to
minimize noise. A simple 1-pole RC filter is sufficient for
many applications.
For example, Figure 9 shows a 470pF capacitor from + AIN
to – AIN and a 30 source resistor to limit the input
bandwidth to 11.3MHz. The 470pF capacitor also acts as
a charge reservoir for the input sample-and-hold and
isolates the amplifier driving VIN from the ADC’s small
current glitch. In undersampling applications, an input
capacitor this large may prohibitively limit the input band-
width. If this is the case, use as large an input capacitance
as possible. High quality capacitors and resistors should
be used since these components can add distortion. NPO
and silver mica type dielectric capacitors have excellent
linearity. Carbon surface mount resistors can generate
distortion from self-heating and from damage that may
occur during soldering. Metal film surface mount resis-
tors are much less susceptible to both problems.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1426IS8#TR | IC DAC PWM 6BIT DUAL MCPWR 8SOIC |
| LTC1427CS8-50#TRPBF | IC D/A CONV 10BIT W/SMBUS 8-SOIC |
| LTC1428CS8-50#TRPBF | IC D/A CONV 8BIT SINK OUT 8-SOIC |
| LTC1446LIS8#TRPBF | IC D/A CONV 12BIT R-R DUAL 8SOIC |
| LTC1448IS8#TRPBF | IC D/A CONV 12BIT R-R DUAL 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1421CG | 功能描述:IC CONTROLLER HOT SWAP 24-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC1421CG#PBF | 功能描述:IC CONTROLLER HOT SWAP 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC1421CG#TR | 功能描述:IC CONTROLLER HOTSWAP ADJ 24SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC1421CG#TRPBF | 功能描述:IC CONTROLLER HOT SWAP 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC1421CG1 | 制造商:Linear Technology 功能描述: |
发布紧急采购，3分钟左右您将得到回复。