- 您现在的位置：买卖IC网 > PDF目录19870 > LTC1422CS8#TRPBF (Linear Technology)IC CONTROLLER HOT SWAP 8-SOIC PDF资料下载
参数资料
| 型号： | LTC1422CS8#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/16页 |
| 文件大小： | 197K |
| 描述： | IC CONTROLLER HOT SWAP 8-SOIC |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 2.7 V ~ 12 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
11
LTC1422
1422fb
plus a Zener voltage (D1) is more positive than the drain
of Q1 (in other words, when the switching FET Q1 has only
7.5V across its drain source).
Hot Swapping 48V Module with Isolated Controller
A power supervisory controller will sometimes reside on
an isolated supply with responsibility for other supplies.
Figure 15 shows how to Hot Swap a controllers 5V supply
and a 48V module using two LTC1422s. Assuming the 5V
supply comes up first, the controller waits for a power
good signal from the 48V circuit. Once it receives the right
signals the controller activates the GATE IN pin of the Vicor
power module.
Power Supply Sequencer
A circuit that forces two supply voltages to power up
together is shown in Figure 16. The input supply voltages
may power up in any sequence, but both input voltages
must be within tolerance before Q1 and Q2 turn on. Back-
to-back transistors Q1 and Q2 ensure isolation between
the two supplies.
When the 5V input powers up before 3.3V, Q1 and Q2
remain off and the 5V output remains off until the 3.3V
input is within tolerance as sensed by resistors R1 and R2.
When the 3.3V input powers up before 5V, the diode D1
will pull up the 5V supply output with it. Once the 5V input
powers up and is within tolerance as sensed by R4 and R5,
Q1 and Q2 will turn on in about 1ms and pull the 5V output
up to its final voltage.
Since the pass transistor is in a common source configu-
ration, care must be taken to limit the inrush current into
capacitor C3. One way is to precharge C3 using resistor
R4. As the input supply is ramping up, current is flowing
through R4 and charging the capacitor C3. Once the input
supply crosses 38V, there is a timing cycle followed by the
ramp-up of the GATE pin. By this time the capacitor C3 is
sufficiently charged, thereby limiting the inrush current.
Another method to limit the inrush current is to slow down
the ramp-up rate of the GATE pin.
Hot Swapping 48V DC/DC Module with
Active High On/Off Control Signal
This application is identical to the previous except for the
polarity of the modules on/off signal. The polarity reversal
is accomplished by transistor Q3 in Figure 13.
Hot Swapping Redundant 48V
In critical situations, redundant input supplies are neces-
sary. In Figure 14 a redundant 48V input is switched to a
power module. Supplies 1 and 2 are wire ORed using two
diodes D2 and D3. This results in the most negative of
these two supplies being used to drive the power module.
If one of the supplies is disconnected or a fuse opens, the
fault signal will be activated via diodes D4 and D5 and the
reset comparator at the FB pin. The GATE IN signal on the
Vicor module is controlled using the high voltage PNP Q2.
Once the modules minus input pin is more negative than
the base of Q2 plus a diode drop, Q2 will turn off and the
module will turn on. This occurs when the source of Q1
1
2
3
4
8
7
6
5
V
CC
SENSE
GATE
FB
RESET
ON
TIMER
GND
LTC1422
1422 F11
Q1
MMFT2N02ELT1
CURRENT LIMIT: 2.5A
Q2
MMFT2N02ELT1
R1
0.02&
5%
R3
10&
5%
R6
1.6M
5%
R7
360k
5%
R2
10&
5%
R4
2.74k
1%
R5
1.62k
1%
Q3
PN2222
C1
0.0033礔
16V
C2
0.1礔
16V
C
LOAD
C3
0.1礔
16V
C
LOAD
V
OUT
3.3V
V
OUT
5V
V
IN
5V
+
+
Figure 11. Switching 5V and Generating 3.3V
APPLICATIONS INFORMATION
U
U
U
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B1J-CY-F2 | CONVERTER MOD DC/DC 36V 50W |
| ATF1504ASVL-20JU44 | IC CPLD 20NS LOWV LOW PWR 44PLCC |
| VI-B1J-CY-F1 | CONVERTER MOD DC/DC 36V 50W |
| ATF1508ASV-15JU84 | IC CPLD 15NS LOW V 84PLCC |
| VI-21J-CY-F3 | CONVERTER MOD DC/DC 36V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1422IN8 | 功能描述:IC CONTROLLER HOT SWAP 8-DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC1422IN8#PBF | 功能描述:IC CONTROLLER HOT SWAP 8-DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC1422IS8 | 功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC1422IS8#PBF | 功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC1422IS8#TR | 功能描述:IC CONTROLLER HOTSWAP 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。