- 您现在的位置：买卖IC网 > PDF目录11035 > LTC1562CG-2#PBF (Linear Technology)IC FILTER UNIV RC QUAD LN 20SSOP PDF资料下载
参数资料
| 型号： | LTC1562CG-2#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | IC FILTER UNIV RC QUAD LN 20SSOP |
| 标准包装： | 66 |
| 滤波器类型： | 通用连续计时 |
| 频率 - 截止或中心： | 300kHz |
| 滤波器数： | 4 |
| 滤波器阶数： | 8th |
| 电源电压： | 4.75 V ~ 10.5 V，±4.75 V ~ 5.25 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 1324 (CN2011-ZH PDF) |
7
LTC1562-2
15622fa
APPLICATIONS INFORMATION
WU
U
The LTC1562-2 contains four matched, 2nd order,
3-terminal universal continuous-time filter blocks, each
with a virtual-ground input node (INV) and two rail-to-rail
outputs (V1, V2). In the most basic application, one such
block and three external resistors provide 2nd order
lowpass and bandpass responses simultaneously (Figure
3, with a resistor for ZIN). The three external resistors
program fO, Q and gain. A combination of internal preci-
sion components and external resistor R2 sets the center
frequency fO of each 2nd order block. The LTC1562-2 is
trimmed at manufacture so that fO will be 200kHz ±0.5%
if the external resistor R2 is exactly 7958
.TheLTC1562-
2 is a higher frequency, pin compatible variant of the
LTC1562, with different internal R and C values and higher
speed amplifiers.
However, lowpass/bandpass filtering is only one specific
application for the 2nd order building blocks in the
LTC1562-2. Highpass response results if the external
impedance ZIN in Figure 3 becomes a capacitor CIN (whose
value sets only gain, not critical frequencies) as described
below. Responses with zeroes (e.g, elliptic or notch
responses) are available by feedforward connections with
multiple 2nd order blocks (see Typical Applicatons). More-
over, the virtual-ground input gives each 2nd order sec-
tion the built-in capability for analog operations such as
gain (preamplification), summing and weighting of mul-
tiple inputs, or accepting current or charge signals di-
rectly. These Operational Filter
TM frequency-selective
building blocks are nearly as versatile as op amps.
The user who is not copying exactly one of the Typical
Applications schematics shown later in this data sheet is
urged to read carefully the next few sections through at
least Signal Swings, for orientation about the LTC1562-2,
before attempting to design custom application circuits.
Also available free from LTC, and recommended for de-
signing custom filters, is the general-purpose analog filter
design software FilterCAD
TM for Windows. This software
includes tools for finding the necessary f0, Q and gain
parameters to meet target filter specifications such as
frequency response.
Setting fO and Q
Each of the four 2nd order sections in the LTC1562-2 can
be programmed for a standard filter function (lowpass,
bandpass or highpass) when configured as in Figure 3
with a resistor or capacitor for ZIN. These transfer func-
tions all have the same denominator, a complex pole pair
with center frequency
ωO = 2πfO and quality parameter Q.
(The numerators depend on the response type as de-
scribed below.) External resistors R2 and RQ set fO and Q
as follows:
f
CR R
R
kHz
Q
R
RR
R
kHz
f
O
QQ
Q
O
==
()
==
()
=
1
21 2
7958
2
200
12
7958
2
200
π ()
()
R1 = 7958
and C = 100pF are internal to the LTC1562-2
while R2 and RQ are external.
A typical design procedure proceeds from the desired fO
and Q as follows, using finite-tolerance fixed resistors.
First find the ideal R2 value for the desired fO:
R Ideal
kHz
fO
2
200
7958
2
() =
()
Then select a practical R2 value from the available finite-
tolerance resistors. Use the actual R2 value to find the
desired RQ, which also will be approximated with finite
tolerance:
RQ
R
Q =
()
7958
2
The fO range is approximately 20kHz to 300kHz, limited
mainly by the magnitudes of the external resistors
required. As shown above, R2 varies with the inverse
square of fO. This relationship desensitizes fO to R2’s
tolerance (by a factor of 2 incrementally), but it also
implies that R2 has a wider range than fO. (RQ and RIN also
Operational Filter and FilterCAD are trademarks of Linear Technology Corporation.
Windows is a registered trademark of Microsoft Corporation.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-JWK-IW-B1 | CONVERTER MOD DC/DC 40V 100W |
| LTC1562CG#PBF | IC FILTER UNIV RC QUAD LN 20SSOP |
| VE-JWJ-IW-B1 | CONVERTER MOD DC/DC 36V 100W |
| LTC1564CG#PBF | IC ANTIALIASING FILTER 16-SSOP |
| LTC6603IUF#PBF | IC FILTER LOWPASS 24-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1562CGPBF | 制造商:Linear Technology 功能描述:Active Filter Quad 8th Order 150kHz SSOP |
| LTC1562CN | 功能描述:IC FILTER UNIV RC QUAD LN 16DIP RoHS:否 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
| LTC1562CN#PBF | 功能描述:IC FILTER UNIV RC QUAD LN 16DIP RoHS:是 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
| LTC1562IG | 功能描述:IC FILTER UNIVRSL RC QUAD 20SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
| LTC1562IG#PBF | 功能描述:IC FILTER UNIV RC QUAD LN 20SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。