- 您现在的位置：买卖IC网 > PDF目录22144 > LTC1644IGN#TR (Linear Technology)IC CONTROLLER HOT SWAP 20-SSOP PDF资料下载
参数资料
| 型号： | LTC1644IGN#TR |
| 厂商： | Linear Technology |
| 文件页数： | 14/24页 |
| 文件大小： | 447K |
| 描述： | IC CONTROLLER HOT SWAP 20-SSOP |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | CompactPCI? |
| 内部开关： | 无 |
| 电源电压： | 3.3V，5V，±12V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 带卷 (TR) |
| 其它名称： | LTC1644IGNTR |
LTC1644
14
1644f
APPLICATIO S I FOR ATIO
U
U
U
Table 2. t
TIMER
vs C
TIMER
C
TIMER
t
TIMER
C
TIMER
t
TIMER
0.01礔
5.24ms
0.22礔
115ms
0.022礔
11.5ms
0.33礔
173ms
0.033礔
17.3ms
0.47礔
246ms
0.047礔
24.6ms
0.68礔
356ms
0.068礔
35.6ms
0.82礔
430ms
0.082礔
43.0ms
1礔
524ms
0.1礔
52.4ms
The TIMER pin is immediately pulled low when the BD_SEL#
signal goes high.
Thermal Shutdown
The internal switches for the 12V and 12V supplies are
protected by an internal current limit and a thermal shut-
down circuit. When the temperature of the chip reaches
130癈, all switches will be latched off and the FAULT pin
(Pin 6) will be pulled low.
Short-Circuit Protection
During a normal power-up sequence, if the TIMER (Pin 4)
is done ramping and any supply is still in current limit, all
of the pass transistors will be immediately turned off and
FAULT (Pin 6) will be pulled low as shown in Figure 4.
In order to prevent excessive power dissipation in the pass
transistors and to prevent voltage spikes on the supplies
during short-circuit conditions, the current limit on each
supply is designed to be a function of the output voltage.
As the output voltage drops, the current limit decreases.
Unlike a traditional circuit breaker function where large
currents can flow before the breaker trips, the current
foldback feature assures that the supply current will be
kept at a safe level. In addition, current foldback prevents
voltage glitches when powering up into a short.
If either the 12V or 12V supply exceeds current limit after
power up, the shorted supplys current will drop immedi-
ately to its I
LIMIT
value. If that supply remains in current
limit for more that 45祍, all of the supplies will be latched
off. The 45祍 delay prevents quick current spikesfor
example, from a fan turning onfrom causing false trips
of the circuit breaker.
After power-up, the 5V and 3.3V supplies are protected
from overcurrent and short-circuit conditions by dual-
level circuit breakers. In the event that either supply
current exceeds the nominal limit but is less than 3 times
the current limit, an internal timer is started. If the supply
is still overcurrent after 45祍, the circuit breaker trips and
all the supplies are turned off (Figure 5). If a short-circuit
occurs and the supply current exceeds 3 times the set
limit, the circuit breakers trip without any delay and the
chip latches off (Figure 6). The chip will stay in the latched
off state until OFF/ON (Pin 5) is cycled high then low or the
12V
IN
(Pin 1) power supply is cycled off then on.
The current limit and the foldback current level for the 5V
and 3.3V outputs are both a function of the external sense
resistor (R1 for 3V
OUT
and R2 for 5V
OUT
, see Figure 1). As
shown in Figure 1, a sense resistor is connected between
5V
IN
(Pin 13) and 5V
SENSE
(Pin 12) for the 5V supply. For
the 3V supply, a sense resistor is connected between 3V
IN
(Pin 9) and 3V
SENSE
(Pin 10). The current limit and the
foldback current level are given by Equations 4 and 5:
I
mV
R
LIMIT XVOUT
SENSE XVOUT
(
)
(
)
=
51
(4)
I
mV
R
FOLDBACK XVOUT
SENSE XVOUT
(
)
(
)
=
12
(5)
where XV
OUT
= 5V
OUT
or 3V
OUT
.
As a design aid, the current limit and foldback level for
commonly used values for R
SENSE
is shown in Table 3.
Table 3. I
LIMIT(XVOUT)
and I
FOLDBACK(XVOUT)
vs R
SENSE
R
SENSE
(&)
I
LIMIT(XVOUT)
I
FOLDBACK(XVOUT)
0.005
10.2A
2.4A
0.006
8.5A
2.0A
0.007
7.3A
1.7A
0.008
6.4A
1.5A
0.009
5.7A
1.3A
0.01
5.1A
1.2A
where XV
OUT
= 3V
OUT
or 5V
OUT
.
The current limit for the internal 12V switch is set at
840mA folding back to 360mA and the 12V switch at
320mA folding back to 100mA.
相关PDF资料 |
PDF描述 |
|---|---|
| EPM7256EGI192-20 | IC MAX 7000 CPLD 256 192-PGA |
| RSC30DRAH-S734 | CONN EDGECARD 60POS .100 R/A PCB |
| R2S12-1524/H | CONV DC/DC 2W 15VIN 24VOUT SMD |
| RMC30DRAH-S734 | CONN EDGECARD 60POS .100 R/A PCB |
| R2S12-1512/H | CONV DC/DC 2W 15VIN 12VOUT SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1645CS | 功能描述:IC CTRLR SEQ HOTSWAP DUAL 14SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC1645CS#PBF | 功能描述:IC CTLR HOT SWAP SEQ DUAL 14SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC1645CS#TR | 功能描述:IC CTRLR SEQ HOTSWAP DUAL 14SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC1645CS#TRPBF | 功能描述:IC CTRLR SEQ HOTSWAP DUAL 14SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC1645CS8 | 功能描述:IC CTRLR SEQ HOTSWAP DUAL 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。