- 您现在的位置：买卖IC网 > PDF目录20109 > LTC1646IGN#PBF (Linear Technology)IC CNTRLR HOTSWAP PCIDUAL 16SSOP PDF资料下载
参数资料
| 型号： | LTC1646IGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/20页 |
| 文件大小： | 407K |
| 描述： | IC CNTRLR HOTSWAP PCIDUAL 16SSOP |
| 标准包装： | 100 |
| 类型： | 热交换控制器 |
| 应用： | CompactPCI? |
| 内部开关： | 无 |
| 电源电压： | 3.3V，5V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
LTC1646
7
1646fa
U
U
PI FU CTIO S
3V
SENSE
(Pin 9): 3.3V Current Limit Set. With a sense
resistor placed in the supply path between 3V
IN
and
3V
SENSE
, the GATE pin voltage will be adjusted to maintain
a constant voltage across the sense resistor and a con-
stant current through the switch while the TIMER pin
voltage is less than 1.25V. A foldback feature makes the
current limit decrease as the voltage at the 3V
OUT
pin
approaches GND.
When the TIMER pin voltage exceeds 1.25V, the circuit
breaker function is enabled. If the voltage across the sense
resistor exceeds 56mV, the circuit breaker is tripped after
a 21祍 time delay. In the event the sense resistor voltage
exceeds 150mV, the circuit breaker trips immediately and
the chip latches off. To disable the 3.3V current limit,
3V
SENSE
and 3V
IN
can be shorted together.
GATE (Pin 10): High Side Gate Drive for the External 3.3V
and 5V N-Channel pass transistors. Requires an external
series RC network for the current limit loop compensation
and setting the minimum ramp-up rate. During power-up,
the slope of the voltage rise at the GATE is set by the 13礎
current source connected to the internal charge pump and
the external capacitor connected to GND or by the 3.3V or
5V current limit and the bulk capacitance on the 3V
OUT
or
5V
OUT
supply lines. During power-down, the slope of the
ramp down voltage is set by the 200礎 current source
connected to GND and the external GATE capacitor.
The voltage at the GATE pin will be modulated to maintain
a constant current when either the 3V or 5V supplies go
into current limit while the TIMER pin voltage is less than
1.25V. If a current fault occurs after the TIMER pin voltage
exceeds 1.25V, the GATE pin is immediately pulled to
GND.
5V
SENSE
(Pin 11): 5V Current Limit Set. With a sense
resistor placed in the supply path between 5V
IN
and
5V
SENSE
, the GATE pin voltage will be adjusted to maintain
a constant voltage across the sense resistor and a con-
stant current through the switch while the TIMER pin
voltage is less than 1.25V. A foldback feature makes the
current limit decrease as the voltage at the 5V
OUT
pin
approaches GND.
When the TIMER pin voltage is greater than 1.25V, the
circuit breaker function is enabled. If the voltage across
the sense resistor exceeds 56mV but is less than 150mV,
the circuit breaker is tripped after a 21祍 time delay. In the
event the sense resistor voltage exceeds 150mV, the
circuit breaker trips immediately and the chip latches off.
To disable the 5V current limit, short 5V
SENSE
and 5V
IN
together.
5V
IN
(Pin 12): 5V Supply Sense Input. An undervoltage
lockout circuit prevents the GATE pin voltage from
ramping up when the voltage at the 5V
IN
pin is less than
2.5V. If no 5V input supply is available, tie the 5V
IN
pin to
the 3V
IN
pin.
PRECHARGE (Pin 13): Precharge Monitor Input. An on-
chip error amplifier with a 1V reference servos the DRIVE
pin voltage to keep the precharge node at 1V. If the
precharge function is not being used, tie the PRECHARGE
pin to GND.
DRIVE (Pin 14): Precharge Base Drive Output. Provides
base drive for an external NPN emitter-follower which in
turn biases the PRECHARGE node. If the precharge func-
tion is not being used, allow the DRIVE pin to float.
OFF/ON (Pin 15): Digital Input. Connect the CPCI BD_SEL#
signal to the OFF/ON pin. When the OFF/ON pin is pulled
low, the GATE pin is pulled high by a 13礎 current source.
When the OFF/ON pin is pulled high the GATE pin will be
pulled to ground by a 200礎 current source.
The OFF/ON pin is also used to reset the electronic circuit
breaker. If the OFF/ON pin is cycled high and low following
the trip of the circuit breaker, the circuit breaker is reset,
and a normal power-up sequence will occur.
RESETIN (Pin 16): Digital Input. Connect the CPCI
PCI_RST# signal to the RESETIN pin. Pulling RESETIN low
will cause the RESETOUT pin to pull low.
相关PDF资料 |
PDF描述 |
|---|---|
| VY2151K29Y5SS6TV0 | CAP CER 150PF 300V 10% RADIAL |
| CENB1010A0603F01 | POWER SUPPLY EXT 12W 6V @ 2A |
| T86C475M025EAAS | CAP TANT 4.7UF 25V 20% 2312 |
| VY2151K29Y5SS63V0 | CAP CER 150PF 300V 10% RADIAL |
| VE-21V-EV-F3 | CONVERTER MOD DC/DC 5.8V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1647-1CS8 | 功能描述:IC CONTROLLR HOTSWAP DUAL 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC1647-1CS8#PBF | 功能描述:IC CTLR HOTSWAP DUAL 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC1647-1CS8#TR | 功能描述:IC CONTROLLER HOTSWAP DUAL 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC1647-1CS8#TRPBF | 功能描述:IC CONTROLLR HOTSWAP DUAL 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC1647-1IS8 | 功能描述:IC CONTROLLER HOTSWAP DUAL 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。