- 您现在的位置：买卖IC网 > PDF目录16023 > LTC1729CS8-8.2 (Linear Technology)IC CTRLR BATT CHRGR LI-ION 8SOIC PDF资料下载
参数资料
| 型号： | LTC1729CS8-8.2 |
| 厂商： | Linear Technology |
| 文件页数： | 5/16页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR BATT CHRGR LI-ION 8SOIC |
| 标准包装： | 100 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
LTC1729 Series
PI FU CTIO S
OVP (Pin 1): Connection to an Internal Precision Resistor
Divider Used as a Voltage Feedback Monitor for Constant-
Voltage Mode Charging.
BAT (Pin 2): Input to Battery Monitor Circuits and OVP
Resistor Divider. The battery monitor circuits activate
trickle charge preconditioning, battery present detection
and C /10 current detection. This pin is in a high impedance
state when V CC is below the undervoltage lockout thresh-
old. During trickle charge preconditioning and charging
the BAT pin sources 12mA and 1.3mA respectively. The
current sources are clamped from driving the BAT pin
above 4.5V/cell with an internal pull-down transistor.
In the No Bat, Done and Pause states or the Hold and Reset
modes, the current sources are turned off, leaving only the
55k OVP divider as a load on the BAT pin. Most chargers
have a 200 μ A current source that will compensate for this
50 μ A to 80 μ A load.
SENSE (Pin 3): Input to C /10 Current Detection Circuit.
This pin sinks 100 μ A during the Charge state which is used
to program the C /10 current threshold.
GND (Pin 4): Ground.
NTC (Pin 5): Input to the NTC Thermistor Monitoring
Circuits. When the voltage on this pin is above 2.79V
(cold) or below 0.405V (hot), the state machine is locked
in the present state and the timer is stopped. This is called
the Hold mode. While in the Hold mode, the charger is
turned off via the V C pin and the current sources on BAT
and SENSE pins are turned off. The STATUS pin is not
If the NTC pin is below 0.2V, the state machine is forced
in the reset mode with all the timers cleared to zero. The
current sources on the BAT pin and SENSE pin are
disabled leaving the 55k OVP divider. The STATUS pin is
pulled low in the Reset mode.
There is a 100 μ A current source on the NTC pin to bias the
NTC thermistor. This current source is active when the V CC
is greater than the undervoltage lockout threshold.
STATUS (Pin 6): Open-Drain Output for C /10 Charge
Termination Detection Circuit. When in the Charge state,
this pin is pulled low. Once the charge current drops below
the C /10 current threshold for three seconds, the pull-
down transistor is disabled, and a 50 μ A pull-down current
sink remains activated until the 1- or 3-hour time-out or
the battery or wall adapter is removed.
V C (Pin 7): Open-Drain Output for Turning Off the Charger.
When this pin is open circuit, the charger is active.
Normally this pin allows the charger to be active for three
hours.
V CC (Pin 8): Input Supply. For 4.1V or 4.2V single cell
operation, V CC should be between 8V and 28V with the IC
turning off when V CC drops below 6V. For 2-cell applica-
tions, the undervoltage lockout is 10.4V with a minimum
V CC of 12V. Removing the wall adapter will trigger an
undervoltage lockout and put the IC in a high impedance
condition. When the supply is connected, the IC is initial-
ized in the Reset mode with the state machine forced in the
Charge state with all the timers set to zero.
affected.
5
相关PDF资料 |
PDF描述 |
|---|---|
| IDCP1813ER180M | INDUCTOR POWER 18UH 0.84A SMD |
| M3CWK-3440K | IDC CABLE - MKC34K/MC34F/MPL34K |
| RBC06DREI-S93 | CONN EDGECARD 12POS .100 EYELET |
| M3UYK-5006J | IDC CABLE - MKS50K/MC50G/MPD50K |
| M3URK-5006J | IDC CABLE - MKS50K/MC50G/MPR50K |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1730EGN-4 | 功能描述:IC BATT PULSE CHRGR LI-ION16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1730EGN-4#PBF | 功能描述:IC BATT PULSE CHRGR LI-ION16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1730EGN-4#TR | 功能描述:IC BATT PULSE CHRGR LI-ION16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1730EGN-4#TRPBF | 功能描述:IC BATT PULSE CHRGR LI-ION16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1730ES8-4.2 | 功能描述:IC BATT PULSE CHRGR LI-ION 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。