- 您现在的位置：买卖IC网 > PDF目录16037 > LTC1730ES8-4.2 (Linear Technology)IC BATT PULSE CHRGR LI-ION 8SOIC PDF资料下载
参数资料
| 型号： | LTC1730ES8-4.2 |
| 厂商： | Linear Technology |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC BATT PULSE CHRGR LI-ION 8SOIC |
| 标准包装： | 100 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.5 V ~ 12 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
LTC1730-4/LTC1730-4.2
APPLICATIO S I FOR ATIO
Surface mount packages rely primarily on the copper leads
Table 1. SO-8 Package Thermal Resistance
(pins) to conduct the heat from the package to the sur-
rounding PC board copper which is acting as a heat sink.
The ground pin is especially important for conducting heat
as well as providing an electrical connection. Use gener-
COPPER AREA
TOPSIDE BACKSIDE
2500mm 2 2500mm 2
1000mm 2 2500mm 2
TOTAL
BOARD AREA
2500mm 2
2500mm 2
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
80 ° C/W
80 ° C/W
ous amounts of copper around the ground pin and also
250mm 2
2500mm 2
2500mm 2
85 ° C/W
consider feedthrough vias (plated through holes) to back-
side or inner copper layers to maximize power dissipation.
Table 1 lists the thermal resistance for the SO-8 package.
Measured values of thermal resistance for several differ-
ent board sizes and copper areas are listed. All measure-
ments were taken in still air on 0.062" FR-4 board with one
ounce copper.
Calculating Junction Temperature
Example: Find the maximum junction temperature for a
battery voltage of 4V (V CC will collapse to approximately
V BAT in the fast charge mode), charge current of 1A and a
maximum ambient temperature of 75 ° C.
The power dissipated by the IC is:
P = (I BAT ? I BAT ? R DS(ON) ) + (V CC ? I CC )
= (1A ? 1A ? 0.35 ? ) + (4V ? 1mA)
= 0.35 + 0.004
= 0.354W
The SO-8 package for the LTC1730 features a special lead
frame with a lower thermal resistance and higher allow-
able power dissipation. The junction-to-ambient thermal
resistance of this package when soldered to a PC board is
approximately 80 ° C/W depending on the copper area. So
the junction temperature rise above ambient will be
approximately:
(0.354W)(80 ° C/W) = 28.3 ° C
The maximum junction temperature is equal to the maxi-
mum junction temperature rise above ambient plus the
maximum ambient temperature or:
*Device is mounted on topside.
Output Voltage Selection (LTC1730EGN-4)
The float voltage at the BAT pin can be selected by the SEL
pin. Shorting the SEL pin to ground will set the float
voltage to 4.1V, while connecting it to V CC sets it to 4.2V.
This feature allows the charger to be used with different
types of Li-Ion cells.
ACPR Output Pin (LTC1730EGN-4)
When the input voltage is 40mV higher than the voltage at
the BAT pin, the ACPR pin is pulled low to ground to
indicate that the input supply (wall adapter) is applied.
After the input supply is removed, this pin becomes high
impedance. An internal 80ms delay prevents the LTC1730
from turning off if the voltage at the V CC pin rings and gets
too close to V BAT because of the parasitic inductance.
FAULT Output Pin (LTC1730EGN-4)
The FAULT pin is pulled to ground when either one of the
following conditions is detected:
1. The voltage at the NTC/SHDN pin is out of the operation
range. With a 10k negative temperature coefficient
thermistor placed near the battery pack, this pin indi-
cates that the temperature of the pack is either too cold
or too hot and the charger is suspended. Once the
temperature is back to the operational range, the FAULT
pin becomes high impedance and the charging re-
sumes.
2. The voltage at the BAT pin stays below 2.45V for 1/4 of
the programmed charge time. If V BAT remains low even
with 35mA of trickle charge current for 1/4 of the total
T JMAX = 75 ° C + 28.3 ° C = 103.3 ° C
sn1730 1730fs
10
相关PDF资料 |
PDF描述 |
|---|---|
| GBM18DTBI-S189 | CONN EDGECARD 36POS R/A .156 SLD |
| A3BRB-5018M | IDC CABLE - ASR50B/AE50M/APR50B |
| M3DYK-4018R | IDC CABLE - MKR40K/MC40M/MPD40K |
| M3BYK-4018R | IDC CABLE - MSR40K/MC40M/MPD40K |
| RCM10DTMS-S189 | CONN EDGECARD 20POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1731EMS8-4.1 | 功能描述:IC CTRLR BATT CHRGR LI-ION 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1731EMS8-4.1#PBF | 功能描述:IC CTRLR BATT CHRGR LI-ION 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1731EMS8-4.1#TR | 功能描述:IC CTRLR BATT CHRGR LI-ION 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1731EMS8-4.1#TRPBF | 功能描述:IC CTRLR BATT CHRGR LI-ION 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1731EMS8-4.2 | 功能描述:IC CTRLR BATT CHRGR LI-ION 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。