参数资料
型号: LTC1735CGN#TRPBF
厂商: Linear Technology
文件页数: 13/32页
文件大小: 0K
描述: IC REG CTRLR BUCK PWM CM 16-SSOP
标准包装: 2,500
PWM 型: 电流模式
输出数: 1
频率 - 最大: 335kHz
占空比: 99.4%
电源电压: 4 V ~ 30 V
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: 0°C ~ 85°C
封装/外壳: 16-SSOP(0.154",3.90mm 宽)
包装: 带卷 (TR)
LTC1735
APPLICATIO S I FOR ATIO
( ) ( )
1 + δ R DS ( ON ) +
P MAIN = OUT I MAX
( ) ( I MAX )( C RSS )( ) f
( ) ( )
1 + δ R
P SYNC = IN OUT I MAX DS ( ON )
Main Switch Duty Cycle = OUT
Synchronous Switch Duty Cycle = IN OUT
Ferrite designs have very low core loss and are preferred
at high switching frequencies, so design goals can con-
centrate on copper loss and preventing saturation. Ferrite
core material saturates “hard,” which means that induc-
tance collapses abruptly when the peak design current is
exceeded. This results in an abrupt increase in inductor
ripple current and consequent output voltage ripple. Do
not allow the core to saturate!
Molypermalloy (from Magnetics, Inc.) is a very good, low
loss core material for toroids, but it is more expensive than
ferrite. A reasonable compromise from the same manu-
facturer is Kool M μ . Toroids are very space efficient,
especially when you can use several layers of wire. Be-
cause they generally lack a bobbin, mounting is more
difficult. However, designs for surface mount are available
that do not increase the height significantly.
Power MOSFET and D1 Selection
Two external power MOSFETs must be selected for use
with the LTC1735: An N-channel MOSFET for the top
(main) switch and an N-channel MOSFET for the bottom
(synchronous) switch.
The peak-to-peak gate drive levels are set by the INTV CC
voltage. This voltage is typically 5.2V during start-up (see
EXTV CC pin connection). Consequently, logic-level thresh-
old MOSFETs must be used in most LTC1735 applica-
tions. The only exception is when low input voltage is
expected (V IN < 5V); then, sub-logic level threshold
MOSFETs (V GS(TH) < 3V) should be used. Pay close
attention to the BV DSS specification for the MOSFETs as
well; many of the logic level MOSFETs are limited to 30V
or less.
Selection criteria for the power MOSFETs include the “ON”
resistance R DS(ON) , reverse transfer capacitance C RSS ,
input voltage and maximum output current. When the
LTC1735 is operating in continuous mode the duty cycles
for the top and bottom MOSFETs are given by:
V
V IN
V – V
V IN
The MOSFET power dissipations at maximum output
current are given by:
V 2
V IN
2
k V IN
V – V 2
V IN
where δ is the temperature dependency of R DS(ON) and k
is a constant inversely related to the gate drive current.
Both MOSFETs have I 2 R losses while the topside
N-channel equation includes an additional term for transi-
tion losses, which are highest at high input voltages. For
V IN < 20V the high current efficiency generally improves
with larger MOSFETs, while for V IN > 20V the transition
losses rapidly increase to the point that the use of a higher
R DS(ON) device with lower C RSS actually provides higher
efficiency. The synchronous MOSFET losses are greatest
at high input voltage or during a short-circuit when the
duty cycle in this switch is nearly 100%.
The term (1 + δ ) is generally given for a MOSFET in the
form of a normalized R DS(ON) vs Temperature curve, but
δ = 0.005/ ° C can be used as an approximation for low
voltage MOSFETs. C RSS is usually specified in the
MOSFET characteristics. The constant k = 1.7 can be
used to estimate the contributions of the two terms in the
main switch dissipation equation.
The Schottky diode D1 shown in Figure 1 conducts during the
dead-time between the conduction of the two power MOSFETs.
This prevents the body diode of the bottom MOSFET from
turning on and storing charge during the dead-time, which
could cost as much as 1% in efficiency. A 3A Schottky is
generally a good size for 10A to 12A regulators due to the
relatively small average current. Larger diodes can result in
additional transition losses due to their larger junction capaci-
tance. The diode may be omitted if the efficiency loss can be
tolerated.
1735fc
13
相关PDF资料
PDF描述
ESC15DRTI-S93 CONN EDGECARD 30POS DIP .100 SLD
LTC3770EUH#PBF IC REG CTRLR BUCK PWM CM 32-QFN
VI-JWF-EW-F1 CONVERTER MOD DC/DC 72V 100W
TVX2W2R2MCD CAP ALUM 2.2UF 450V 20% AXIAL
VE-JWB-EY-F2 CONVERTER MOD DC/DC 95V 50W
相关代理商/技术参数
参数描述
LTC1735CS 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR)
LTC1735CS#PBF 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR
LTC1735CS#TR 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR)
LTC1735CS#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR)
LTC1735CS-1 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR)