- 您现在的位置：买卖IC网 > PDF目录10531 > LTC1856CG#PBF (Linear Technology)IC ADC 16BIT 100KSPS 28-SSOP PDF资料下载
参数资料
| 型号： | LTC1856CG#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 5/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 100KSPS 28-SSOP |
| 标准包装： | 47 |
| 位数： | 16 |
| 采样率（每秒）： | 100k |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 40mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
| 输入数目和类型： | 8 个单端，双极；4 个差分，双极 |
| 产品目录页面： | 1347 (CN2011-ZH PDF) |
13
LTC1854/LTC1855/LTC1856
185456fa
OVERVIEW
The LTC1854/LTC1855/LTC1856 are innovative, multi-
channel ADCs. The on-chip resistors provide attenuation
and offset for each channel. The precisely trimmed attenu-
ators ensure an accurate input range. Because they pre-
cede the multiplexer, errors due to multiplexer
on-resistance are eliminated.
The input word selects the single ended or differential
inputs for each channel or pair of channels. Overrange
protection is provided for unselected channels. An
overrange condition on an unused channel will not affect
the conversion result on the selected channel.
CONVERSION DETAILS
The LTC1854/LTC1855/LTC1856 use a successive approxi-
mation algorithm and an internal sample-and-hold circuit
to convert an analog signal to a 12-/14-/16-bit serial out-
put respectively. The ADCs are complete with a precision
reference and an internal clock. The control logic provides
easy interface to microprocessors and DSPs. (Please refer
to the Digital Interface section for the data format.)
The analog signals applied at the MUX input channels are
rescaled by the resistor divider network formed by R1, R2
and R3 as shown below. The rescaled signals appear on
the MUXOUT (Pins 10, 11) which are also connected to the
ADC inputs (Pins 12, 13) under normal operation.
APPLICATIO S I FOR ATIO
WU
UU
Before starting a conversion, an 8-bit data word is clocked
into the SDI input on the first eight rising SCK edges to
select the MUX address and power down mode. The ADC
enters acquisition mode on the falling edge of the sixth
clock in the 8-bit data word and ends on the rising edge of
the CONVST signal which also starts a conversion (see
Figure 7). A minimum time of 4
mswillprovideenoughtime
for the sample-and-hold capacitors to acquire the analog
signal. Once a conversion cycle has begun, it cannot be
restarted.
During the conversion, the internal differential 12-/14-/16-
bit capacitive DAC output is sequenced by the SAR from the
most significant bit (MSB) to the least significant bit (LSB).
The input is successively compared with the binary
weighted charges supplied by the differential capacitive
DAC. Bit decisions are made by a high speed comparator.
At the end of a conversion, the DAC output balances the
analog input (ADC+ – ADC–). The SAR contents (a 12-/14-
/16-bit data word) which represents the difference of ADC+
and ADC– are loaded into the 12-/14-/16-bit shift register.
DRIVING THE ANALOG INPUTS
The input range for the LTC1854/LTC1855/LTC1856 is
±10V and the MUX inputs are overvoltage protected to
±30V. The input impedance is typically 31kW; therefore, it
should be driven with a low impedance source. Wideband
noise coupling into the input can be minimized by placing
a 3000pF capacitor at the input as shown in Figure 2. An
NPO-type capacitor gives the lowest distortion. Place the
capacitor as close to the device input pin as possible. If an
amplifier is to be used to drive the input, care should be
taken to select an amplifier with adequate accuracy, linear-
ity and noise for the application. The following list is a
summary of the op amps that are suitable for driving the
LTC1854/LTC1855/LTC1856. More detailed information
is available in the Linear Technology data books and online
at www.linear.com.
LT
1007: Low noise precision amplifier. 2.7mA supply
current
±5V to ±15V supplies. Gain bandwidth product
8MHz. DC applications.
MUX
INPUT
R1
25k
REFCOMP
CH SEL
R3
10k
18545 AI01
R2
17k
MUXOUT
相关PDF资料 |
PDF描述 |
|---|---|
| MS3102A24-16P | CONN RCPT 7POS BOX MNT W/PINS |
| VI-J42-MW-F1 | CONVERTER MOD DC/DC 15V 100W |
| LTC2351HUH-14#PBF | IC ADC 14BIT 1.5MSPS 32-QFN |
| MS3102C20-33P | CONN RCPT 11POS BOX MNT W/PINS |
| AD7892ARZ-2 | IC ADC 12BIT LP 500KSPS 24SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1856IG#PBF | 功能描述:IC ADC 16BIT 100KSPS 28-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC1856IG#TRPBF | 功能描述:IC ADC 16BIT 100KSPS 28-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| LTC1857CG | 制造商:Linear Technology 功能描述:ADC Single SAR 100ksps 12-bit Serial 28-Pin SSOP |
| LTC1857CG#PBF | 功能描述:IC ADC 8CH 12BIT 100KSPS 28-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:SoftSpan™ 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC1857CG#PBF | 制造商:Linear Technology 功能描述:ADC, 8CH, 12BIT, 100KSPS, SSOP-28 |
发布紧急采购，3分钟左右您将得到回复。