- 您现在的位置：买卖IC网 > PDF目录15248 > LTC1876EG#PBF (Linear Technology)IC REG CTRLR BST PWM CM 36-SSOP PDF资料下载
参数资料
| 型号： | LTC1876EG#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/36页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM CM 36-SSOP |
| 标准包装： | 37 |
| 系列： | PolyPhase® |
| PWM 型： | 电流模式 |
| 输出数： | 3 |
| 频率 - 最大： | 360kHz |
| 占空比： | 99.4% |
| 电源电压： | 3.5 V ~ 36 V |
| 降压： | 是 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 36-SSOP（0.209"，5.30mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 1333 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC1876
PI N FU N CTIO N S
provides a common control point to shut down both control-
lers. See the Operation section for details.
FCB (Pin 7): Forced Continuous Control Input. This input acts
on both controllers and is normally used to regulate a
secondary winding. Pulling this pin below 0.8V will force
continuous synchronous operation on both controllers. Do
not leave this pin floating.
I TH1, I TH2 (Pins 8, 11): Error Amplifier Output and Switching
Regulator Compensation Point. Each associated channel’s
current comparator trip point increases with this control
voltage.
SGND (Pin 9): Small signal ground common to both control-
lers, must be routed separately from high current grounds to
the common (–) terminals of the C OUT capacitors.
3.3V OUT (Pin 10): Output of a linear regulator capable of
supplying up to 10mA DC with peak currents as high as
50mA.
AUXSGND (Pin 15): Small Signal Ground of the Auxiliary
Boost Regulator.
AUXV FB (Pin 16): Auxiliary Boost Regulator Feedback Volt-
age. This pin receives the feedback voltage from an external
resistive divider across the auxiliary output.
AUXSW (Pins 17, 18): Switch Node Connections to Inductor
for the Auxiliary Regulator. Voltage swing at these pins are
from ground to (V OUT + voltage across Shottky diode).
Minimize trace area at these pins to keep EMI down.
AUXPGND (Pins 19, 20): The Auxiliary Power Ground Pins.
Its gate drive currents are returned to these pin.
AUXV IN (Pin 21): Auxiliary Boost Regulator Controller Sup-
ply Pin. Must be closely decoupled to AUXPGND.
AUXSD (Pin 22): Shutdown Pin for the Auxiliary Regulator.
Connect to 2.4V or more to enable the auxiliary regulator or
ground to shut the auxiliary regulator off.
TG1, TG2 (Pins 35, 24): High Current Gate Drives for Top
N-Channel MOSFETs. These are the outputs of floating
drivers with a voltage swing equal to INTV CC – 0.5V superim-
posed on the switch node voltage SW.
SW1, SW2 (Pins 34, 25): Switch Node Connections to
Inductors. Voltage swing at these pins is from a Schottky
diode (external) voltage drop below ground to V IN .
BOOST1, BOOST2 (Pins 33, 26): Bootstrapped Supplies to
the Top Side Floating Drivers. Capacitors are connected
between the boost and switch pins and Schottky diodes are
tied between the boost and INTV CC pins. Voltage swing at the
boost pins is from INTV CC to (V IN + INTV CC ).
BG1, BG2 (Pins 31, 27): High Current Gate Drives for Bottom
(synchronous) N-Channel MOSFETs. Voltage swing at these
pins is from ground to INTV CC .
PGND (Pin 28): Driver Power Ground. Connects to sources
of bottom (synchronous) N-channel MOSFETs, anode of the
Schottky rectifier and the (–) terminal(s) of C IN .
INTV CC (Pin 29): Output of the Internal 5V Linear Low
Dropout Regulator and the EXTV CC Switch. The driver and
control circuits are powered from this voltage source. Must
be decoupled to power ground with a minimum of 4.7 μ F
tantalum or other, low ESR capacitor. The INTV CC regulator
standby operation is determined by the STBYMD pin.
EXTV CC (Pin 30): External Power Input to an Internal Switch
Connected to INTV CC . This switch closes and supplies V CC
power, bypassing the internal low dropout regulator, when-
ever EXTV CC is higher than 4.7V. See EXTV CC connection in
Applications section. Do not exceed 7V on this pin .
V IN (Pin 32): Main Supply Pin. A bypass capacitor should be
tied between this pin and the signal ground pin.
PGOOD (Pin 36): Open-Drain Logic Output. PGOOD is pulled
to ground when the voltage on either V OSENSE pin is not within
7.5% of its setpoint.
1876fa
9
相关PDF资料 |
PDF描述 |
|---|---|
| CAT809MTBI-T3 | IC VOLTAGE SUPERVISOR SOT-23-3 |
| ELL-3GM3R9N | COIL PWR CHOKE 3.9UH 940MA SMD |
| CAT809JTBI-T3 | IC VOLTAGE SUPERVISOR SOT-23-3 |
| ELL-3GM3R3N | COIL PWR CHOKE 3.3UH 980MA SMD |
| RCC43DCAH-S189 | CONN EDGECARD 86POS R/A .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1877EMS8 | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC1877EMS8#PBF | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC1877EMS8#TR | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC1877EMS8#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC1877EMS8PBF | 制造商:Linear Technology 功能描述:1.5A Regulator Step Down LTC1877EMS8 |
发布紧急采购，3分钟左右您将得到回复。