- 您现在的位置：买卖IC网 > PDF目录15972 > LTC1960CUHF#TRPBF (Linear Technology)IC BATT CHRGR/SELECTR DL 38-QFN PDF资料下载
参数资料
| 型号： | LTC1960CUHF#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/28页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHRGR/SELECTR DL 38-QFN |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电源电压： | 6 V ~ 28 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC1960
OPERATION
R VF
–
V SET
EA
11
?Σ
MODULATOR
bitissetinthestatusregister.Thisisathree-strikes-and-
you’re-out process which is intended to debounce the
PowerPath PF indicator. The power-fail counter is reset
by a PowerPath SPI write.
Short-Circuit Protection
Short-circuit protection operates in both a current mode
and a voltage mode. If the voltage between SCP and SCN
exceeds the short-circuit comparator threshold V TSC for
more than 15ms, then all of the PowerPath switches are
turned off and the FAULT bit (FA) is set. Similarly, if the
voltage at SCN falls below 3V for more than 15ms, then
all of the PowerPath switches are turned off and the FA bit
is set. The FA bit is reset by removing all power sources
and allowing the voltage at V PLUS to fall below the UVLO
threshold. If the FA bit is set, charging is disabled until
V PLUS exceeds the UVLO threshold and charging is re-
quested via the SPI interface.
When a hard short-circuit occurs, it might pull all of the
power sources down to near 0V potentials. The capacitors
on V CC and V PLUS must be large enough to keep the circuit
operating correctly during the 15ms short-circuit event.
The charger will stop within a few microseconds leaving
a small current which must be provided by the capacitor
on V PLUS . The recommended minimum values (1μF on
V PLUS and 2μF on V CC , including tolerances) should keep
the LTC1960 operating above the UVLO trip voltage long
enough to perform the short-circuit function when the
input voltages are greater than 8V. Increasing the capaci-
tor across V CC to 4.7μF will allow operation down to the
recommended 6V minimum.
Fast PowerPath Turn-Off
All of the PowerPath switches can be forced off by set-
ting the DCDIV pin to a voltage between 8V and 10V. This
will have the same effect as a short-circuit event. The PF
status bit will also be set. DCDIV must be less than 5V
and V PLUS must decrease below the UVLO threshold to
re-enable the PowerPath switches.
Power-Up Strategy
All three PowerPath switches are turned on after V PLUS
exceeds the UVLO threshold for more than 250ms. This
delay is to prevent oscillation from a turn-on transient
near the UVLO threshold.
The Voltage DAC Block
The voltage DAC (VDAC) is a delta-sigma modulator
which controls the effective value of an internal resistor,
R VSET = 7.2k, used to program the maximum charger
voltage. Figure 5 is a simplified diagram of the VDAC
operation. The charger monitor MUX is connected to the
appropriate battery indicated by the CHARGE_BATx bit.
The delta-sigma modulator and switch SWV convert the
VDAC value, received via SPI communication, to a vari-
able resistance equal to (11/8)R VSET /(VDAC (VALUE) /2047).
In regulation, V SET is servo driven to the 0.8V reference
voltage, V REF .
Therefore, programmed voltage is:
V BATx = (8/11) V REF 405.3k/7.2k ? (VDAC (VALUE) /2047)
+ V REF = 32,752mV ? (VDAC (VALUE) /2047) + 0.8V
Note that the reference voltage must be subtracted from
the VDAC value in order to obtain the correct output volt-
age. This value is V REF /16mV = 50 (32 HEX ).
Capacitors C B1 and C B2 are used to average the voltage
present at the V SET pin as well as provide a zero in the
voltage loop to help stability and transient response time
to voltage variations. See the Applications Information
section.
BAT1 CHGMON
BAT2
C B2 405.3k
CSN
TO
C B1 I TH
V REF +
R VSET
7.2k
DAC
SWV VALUE
(11 BITS)
1960 F05
Figure 5. Voltage DAC Operation
1960fb
17
相关PDF资料 |
PDF描述 |
|---|---|
| RCM24DRMH | CONN EDGECARD 48POS .156 WW |
| MAX6366LKA29+T | IC SUPERVISOR MPU LP SOT23-8 |
| 63YXG820MEFC18X25 | CAP ALUM 820UF 63V 20% RADIAL |
| LTC1960CUHF#PBF | IC BATT CHRGR/SELECTR DL 38-QFN |
| RCM22DRKI | CONN EDGECARD 44POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1966CMS8 | 功能描述:IC PREC RMS/DC CONV MCRPWR 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - RMS 至 DC 转换器 系列:- 标准包装:46 系列:- 电流 - 电源:1.2mA 电源电压:±18 V，36 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:管件 |
| LTC1966CMS8#PBF | 功能描述:IC PREC RMS/DC CONV MCRPWR 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - RMS 至 DC 转换器 系列:- 标准包装:46 系列:- 电流 - 电源:1.2mA 电源电压:±18 V，36 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:管件 |
| LTC1966CMS8#TR | 功能描述:IC PREC RMS/DC CONV MCRPWR 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - RMS 至 DC 转换器 系列:- 标准包装:46 系列:- 电流 - 电源:1.2mA 电源电压:±18 V，36 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:管件 |
| LTC1966CMS8#TRPBF | 功能描述:IC PREC RMS/DC CONV MCRPWR 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - RMS 至 DC 转换器 系列:- 标准包装:46 系列:- 电流 - 电源:1.2mA 电源电压:±18 V，36 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:管件 |
| LTC1966CMS8PBF | 制造商:Linear Technology 功能描述:RMS-to-DC Converter Prec. uPower MSOP8 |
发布紧急采购，3分钟左右您将得到回复。