- 您现在的位置：买卖IC网 > PDF目录39413 > LTC2202I (LINEAR TECHNOLOGY CORP) 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 PDF资料下载
参数资料
| 型号： | LTC2202I |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | ADC |
| 英文描述： | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 |
| 封装： | 7 X 7 MM, PLASTIC, MO-220-WKKD-2, QFN-48 |
| 文件页数： | 14/26页 |
| 文件大小： | 1118K |
| 代理商： | LTC2202I |
LTC2203/LTC2202
21
22032p
APPLICATIO S I FOR ATIO
W
U
An on-chip clock duty cycle stabilizer may be activated if
the input clock does not have a 50% duty cycle. This circuit
uses the falling edge of CLK pin to sample the analog input.
The rising edge of CLK is ignored and an internal rising
edge is generated by a phase-locked loop. The input clock
duty cycle can vary from 30% to 70% and the clock duty
cycle stabilizer will maintain a constant 50% internal duty
cycle. If the clock is turned off for a long period of time,
the duty cycle stabilizer circuit will require one hundred
clock cycles for the PLL to lock onto the input clock. To
use the clock duty cycle stabilizer, the MODE pin must be
connected to 1/3VDD or 2/3VDD using external resistors.
The lower limit of the LTC2203/LTC2202 sample rate is
determined by droop of the sample and hold circuits. The
pipelined architecture of this ADC relies on storing analog
signals on small valued capacitors. Junction leakage will
dischargethecapacitors.Thespeciedminimumoperating
frequency for the LTC2203/LTC2202 is 1Msps.
DIGITAL OUTPUTS
Digital Output Buffers
Figure 9 shows an equivalent circuit for a single output
buffer in CMOS Mode. Each buffer is powered by OVDD
and OGND, isolated from the ADC power and ground. The
additional N-channel transistor in the output driver allows
operation down to low voltages. The internal resistor in
series with the output makes the output appear as 50Ω
to external circuitry and eliminates the need for external
damping resistors.
Figure 8. Sinusoidal Single-Ended CLK Drive
CLK
0.1
F
0.1
F
4.7
F
1k
FERRITE
BEAD
CLEAN 3.3V
SUPPLY
SINUSOIDAL
CLOCK
INPUT
22032 F09
NC7SVU04
LTC2203/02
56
higher for input frequencies above 100MHz. For applica-
tions with high input frequencies, the low input range will
have improved distortion; however, the SNR will be 2.4dB
worse. See the typical performance curves section.
Driving the Clock Input
The CLK input can be driven directly with a CMOS or TTL
level signal. A sinusoidal clock can also be used along
with a low-jitter squaring circuit before the CLK pin (see
Figure 8).
The noise performance of the LTC2203/2202 can depend
on the clock signal quality as much as on the analog
input. Any noise present on the clock signal will result in
additional aperture jitter that will be RMS summed with
the inherent ADC aperture jitter.
In applications where jitter is critical, such as when digi-
tizing high input frequencies, use as large an amplitude
as possible. Also, if the ADC is clocked with a sinusoidal
signal, lter the CLK signal to reduce wideband noise and
distortion products generated by the source.
Maximum and Minimum Conversion Rates
ThemaximumconversionratefortheLTC2203is25Msps.
ThemaximumconversionratefortheLTC2202is10Msps.
FortheADCtooperateproperlytheCLKsignalshouldhave
a 50% (±5%) duty cycle. Each half cycle must have at least
18.9ns for the LTC2203 internal circuitry to have enough
settling time for proper operation. For the LTC2202, each
half cycle must be at least 40ns.
Figure 9. Equivalent Circuit for a Digital Output Buffer
LTC2203/02
22032 F10
OVDD
VDD
0.1
F
TYPICAL
DATA
OUTPUT
OGND
43
OVDD 0.5V
TO 3.6V
PREDRIVER
LOGIC
DATA
FROM
LATCH
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2202I#PBF | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 |
| LTC2202I#TR | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 |
| LTC2203C#PBF | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 |
| LTC2203I | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 |
| LTC2202C | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2202IUK | 制造商:Linear Technology 功能描述:ADC Single Pipelined 10Msps 16-bit Parallel 48-Pin QFN EP |
| LTC2202IUK#PBF | 功能描述:IC ADC 16-BIT 10MSPS 48-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2202IUK#TRPBF | 功能描述:IC ADC 16-BIT 10MSPS 48-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC2202UK | 制造商:LINER 制造商全称:Linear Technology 功能描述:16-Bit, 25Msps/10Msps ADCs |
| LTC2203 | 制造商:LINER 制造商全称:Linear Technology 功能描述:16-Bit, 25Msps/10Msps ADCs |
发布紧急采购，3分钟左右您将得到回复。