- 您现在的位置：买卖IC网 > PDF目录10068 > LTC2222IUK#TRPBF (Linear Technology)IC ADC 12BIT 105MSPS SAMPL 48QFN PDF资料下载
参数资料
| 型号： | LTC2222IUK#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 105MSPS SAMPL 48QFN |
| 标准包装： | 2,000 |
| 位数： | 12 |
| 采样率（每秒）： | 105M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 535mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN-EP（7x7） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个单端，双极; 1 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC2222/LTC2223
18
22223fb
APPLICATIONS INFORMATION
Figure 4 demonstrates the use of a differential amplier to
convert a single ended input signal into a differential input
signal. The advantage of this method is that it provides
low frequency input response; however, the limited gain
bandwidth of most op amps will limit the SFDR at high
input frequencies.
Figure 5 shows a single-ended input circuit. The impedance
seen by the analog inputs should be matched. This circuit
is not recommended if low distortion is required.
The 25Ω resistors and 12pF capacitor on the analog inputs
serve two purposes: isolating the drive circuitry from
the sample-and-hold charging glitches and limiting the
wideband noise at the converter input. For input frequen-
cies higher than 100MHz, the capacitor may need to be
decreased to prevent excessive signal loss.
For input frequencies above 100MHz the input circuits of
Figure 6, 7 and 8 are recommended. The balun transformer
gives better high frequency response than a ux coupled
center tapped transformer. The coupling capacitors allow
the analog inputs to be DC biased at 1.6V. In Figure 8 the
series inductors are impedance matching elements that
maximize the ADC bandwidth.
Reference Operation
Figure 9 shows the LTC2222/LTC2223 reference circuitry
consisting of a 1.6V bandgap reference, a difference ampli-
er and switching and control circuit. The internal voltage
reference can be congured for two pin selectable input
ranges of 2V (±1V differential) or 1V (±0.5V differential).
Tying the SENSE pin to VDD selects the 2V range; typing
the SENSE pin to VCM selects the 1V range.
The 1.6V bandgap reference serves two functions: its
output provides a DC bias point for setting the common
mode voltage of any external input circuitry; additionally,
the reference is used with a difference amplier to gener-
ate the differential reference levels needed by the internal
ADC circuitry. An external bypass capacitor is required
for the 1.6V reference output, VCM. This provides a high
frequency low impedance path to ground for internal and
external circuitry.
The difference amplier generates the high and low
reference for the ADC. High speed switching circuits are
connected to these outputs and they must be externally
bypassed. Each output has four pins: two each of REFHA
and REFHB for the high reference and two each of REFLA
and REFLB for the low reference. The multiple output pins
are needed to reduce package inductance. Bypass capaci-
tors must be connected as shown in Figure 9.
Other voltage ranges in between the pin selectable ranges
can be programmed with two external resistors as shown
in Figure 10. An external reference can be used by ap-
plying its output directly or through a resistor divider to
SENSE. It is not recommended to drive the SENSE pin
with a logic device. The SENSE pin should be tied to the
appropriate level as close to the converter as possible. If
the SENSE pin is driven externally, it should be bypassed
to ground as close to the device as possible with a 1μF
ceramic capacitor.
相关PDF资料 |
PDF描述 |
|---|---|
| MS3108E18-12P | CONN PLUG 6POS RT ANG W/PINS |
| VI-26P-MX-F2 | CONVERTER MOD DC/DC 13.8V 75W |
| LT1330CG#PBF | IC TXRX 5V RS232 W/3VLOGC 28SSOP |
| LT1330CG | IC TXRX 5V RS232 W/3VLOGC 28SSOP |
| IDT72241L10J8 | IC FIFO 2048X18 SYNC 10NS 32PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2222UK | 制造商:LINER 制造商全称:Linear Technology 功能描述:12-Bit,105Msps/80Msps ADCs |
| LTC2222UK-11 | 制造商:LINER 制造商全称:Linear Technology 功能描述:11-Bit, 105Msps ADC |
| LTC2223 | 制造商:LINER 制造商全称:Linear Technology 功能描述:12-Bit,105Msps/80Msps ADCs |
| LTC2223CUK | 功能描述:IC ADC 12BIT 80MSPS SAMPLE 48QFN RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| LTC2223CUK#PBF | 功能描述:IC ADC 12BIT 80MSPS SAMPLE 48QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
发布紧急采购，3分钟左右您将得到回复。