- 您现在的位置：买卖IC网 > PDF目录10225 > LTC2232IUK#TR (Linear Technology)IC ADC 10BIT 105MSPS SAMPL 48QFN PDF资料下载
参数资料
| 型号： | LTC2232IUK#TR |
| 厂商： | Linear Technology |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 105MSPS SAMPL 48QFN |
| 标准包装： | 2,000 |
| 位数： | 10 |
| 采样率（每秒）： | 105M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 535mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN-EP（7x7） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个单端，双极; 1 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC2232/LTC2233
20
22323fa
Input Range
The input range can be set based on the application. The
2V input range will provide the best signal-to-noise perfor-
mance while maintaining excellent SFDR. The 1V input
range will have better SFDR performance, but the SNR will
degrade by 1.5dB. See the Typical Performance Charac-
teristics section.
Driving the Encode Inputs
The noise performance of the LTC2232/LTC2233 can
depend on the encode signal quality as much as on the
analog input. The ENC+/ENC– inputs are intended to be
driven differentially, primarily for noise immunity from
common mode noise sources. Each input is biased through
a 6k resistor to a 1.6V bias. The bias resistors set the DC
operating point for transformer coupled drive circuits and
can set the logic threshold for single-ended drive circuits.
Any noise present on the encode signal will result in
additional aperture jitter that will be RMS summed with the
inherent ADC aperture jitter.
In applications where jitter is critical (high input frequen-
cies) take the following into consideration:
1. Differential drive should be used.
2. Use as large an amplitude as possible; if transformer
coupled use a higher turns ratio to increase the amplitude.
3. If the ADC is clocked with a sinusoidal signal, filter the
encode signal to reduce wideband noise.
4. Balance the capacitance and series resistance at both
encode inputs so that any coupled noise will appear at both
inputs as common mode noise. The encode inputs have a
common mode range of 1.1V to 2.5V. Each input may be
driven from ground to VDD for single-ended drive.
Maximum and Minimum Encode Rates
The maximum encode rate for the LTC2232/LTC2233 is
105Msps (LTC2232) and 80Msps (LTC2233). For the ADC
to operate properly, the encode signal should have a 50%
(
±5%) duty cycle. Each half cycle must have at least 4.5ns
(LTC2232) or 5.9ns (LTC2233) for the ADC internal cir-
cuitry to have enough settling time for proper operation.
Achieving a precise 50% duty cycle is easy with differential
sinusoidal drive using a transformer or using symmetric
differential logic such as PECL or LVDS.
An optional clock duty cycle stabilizer circuit can be used
if the input clock has a non 50% duty cycle. This circuit
uses the rising edge of the ENC+ pin to sample the analog
input. The falling edge of ENC+ is ignored and the internal
falling edge is generated by a phase-locked loop. The input
clock duty cycle can vary from 20% to 80% and the clock
duty cycle stabilizer will maintain a constant 50% internal
duty cycle. If the clock is turned off for a long period of
time, the duty cycle stabilizer circuit will require a hundred
clock cycles for the PLL to lock onto the input clock. To use
the clock duty cycle stabilizer, the MODE pin should be
connected to 1/3VDD or 2/3VDD using external resistors.
APPLICATIO S I FOR ATIO
WU
UU
Figure 11. Transformer Driven ENC+/ENC–
VDD
LTC2232/LTC2233
22323 F11
VDD
ENC–
ENC+
1.6V BIAS
1:4
0.1
F
CLOCK
INPUT
50
6k
TO INTERNAL
ADC CIRCUITS
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1276BCN#PBF | IC A/D CONV 12BIT SAMPLING 24DIP |
| LTC1276BCN | IC A/D CONV 12BIT SAMPLING 24DIP |
| SP3222ECY-L/TR | IC TXRX RS232 ESD TRUE 20TSSOP |
| ADM4857ARZ-REEL7 | IC TXRX RS485/422 10MBPS 8SOIC |
| LTC1275BCN | IC A/D CONV 12BIT SAMPLING 24DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2232UK | 制造商:LINER 制造商全称:Linear Technology 功能描述:10-Bit,105Msps/80Msps ADCs |
| LTC2233 | 制造商:LINER 制造商全称:Linear Technology 功能描述:14-Bit, 80Msps Low Power 3V ADC |
| LTC2233CUK | 功能描述:IC ADC 10BIT 80MSPS SAMPL 48QFN RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2233CUK#PBF | 功能描述:IC ADC 10BIT 80MSPS SAMPLE 48QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2233CUK#TR | 功能描述:IC ADC 10BIT 80MSPS SAMPL 48QFN RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。