- 您现在的位置：买卖IC网 > PDF目录2005 > LTC2237IUH#TRPBF (Linear Technology)IC ADC 10BIT 40MSPS 3V 32-QFN PDF资料下载
参数资料
| 型号： | LTC2237IUH#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 40MSPS 3V 32-QFN |
| 标准包装： | 2,500 |
| 位数： | 10 |
| 采样率（每秒）： | 40M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 144mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个单端，双极; 1 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC2238/LTC2237/LTC2236
16
223876fa
Single-Ended Input
For cost sensitive applications, the analog inputs can be
driven single-ended. With a single-ended input the har-
monic distortion and INL will degrade, but the SNR and
DNL will remain unchanged. For a single-ended input, AIN+
should be driven with the input signal and AIN– should be
connected to 1.5V or VCM.
Common Mode Bias
For optimal performance the analog inputs should be
driven differentially. Each input should swing
±0.5V for
the 2V range or
±0.25V for the 1V range, around a
common mode voltage of 1.5V. The VCM output pin (Pin
31) may be used to provide the common mode bias level.
VCM can be tied directly to the center tap of a transformer
to set the DC input level or as a reference level to an op amp
differential driver circuit. The VCM pin must be bypassed to
ground close to the ADC with a 2.2
F or greater capacitor.
Input Drive Impedance
As with all high performance, high speed ADCs, the
dynamic performance of the LTC2238/LTC2237/LTC2236
can be influenced by the input drive circuitry, particularly
the second and third harmonics. Source impedance and
reactance can influence SFDR. At the falling edge of CLK,
the sample-and-hold circuit will connect the 4pF sampling
capacitor to the input pin and start the sampling period.
The sampling period ends when CLK rises, holding the
sampled input on the sampling capacitor. Ideally the input
circuitry should be fast enough to fully charge
the sampling capacitor during the sampling period
APPLICATIO S I FOR ATIO
WU
UU
1/(2FENCODE); however, this is not always possible and the
incomplete settling may degrade the SFDR. The sampling
glitch has been designed to be as linear as possible to
minimize the effects of incomplete settling.
For the best performance, it is recommended to have a
source impedance of 100
or less for each input. The
source impedance should be matched for the differential
inputs. Poor matching will result in higher even order
harmonics, especially the second.
Input Drive Circuits
Figure 3 shows the LTC2238/LTC2237/LTC2236 being
driven by an RF transformer with a center tapped second-
ary. The secondary center tap is DC biased with VCM,
setting the ADC input signal at its optimum DC level.
Terminating on the transformer secondary is desirable, as
this provides a common mode path for charging glitches
caused by the sample and hold. Figure 3 shows a 1:1 turns
ratio transformer. Other turns ratios can be used if the
source impedance seen by the ADC does not exceed 100
for each ADC input. A disadvantage of using a transformer
is the loss of low frequency response. Most small RF
transformers have poor performance at frequencies be-
low 1MHz.
Figure 4 demonstrates the use of a differential amplifier to
convert a single ended input signal into a differential input
signal. The advantage of this method is that it provides low
frequency input response; however, the limited gain band-
width of most op amps will limit the SFDR at high input
frequencies.
Figure 3. Single-Ended to Differential Conversion Using a Transformer
25
25
25
25
0.1
F
AIN
+
AIN
–
12pF
2.2
F
VCM
LTC2238
LTC2237
LTC2236
ANALOG
INPUT
0.1
FT1
1:1
T1 = MA/COM ETC1-1T
RESISTORS, CAPACITORS
ARE 0402 PACKAGE SIZE
223876 F03
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2239CUH#PBF | IC ADC 10-BIT 80MSPS 3V 32-QFN |
| LTC2240CUP-12#PBF | IC ADC 12BIT 170MSPS 64-QFN |
| LTC2240IUP-10#PBF | IC ADC 10BIT 170MSPS 64-QFN |
| LTC2241IUP-10#PBF | IC ADC 10BIT 210MSPS 64-QFN |
| LTC2242IUP-10#PBF | IC ADC 10BIT 250MSPS 64-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2238 | 制造商:LINER 制造商全称:Linear Technology 功能描述:14-Bit, 80Msps Low Power 3V ADC |
| LTC2238CUH | 制造商:Linear Technology 功能描述:ADC Single Pipelined 65Msps 10-bit Parallel 32-Pin QFN EP |
| LTC2238CUH#PBF | 功能描述:IC ADC 10-BIT 65MSPS 3V 32-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2238CUH#TRPBF | 功能描述:IC ADC 10BIT 65MSPS 3V 32-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2238IUH | 制造商:Linear Technology 功能描述:ADC Single Pipelined 65Msps 10-bit Parallel 32-Pin QFN EP |
发布紧急采购，3分钟左右您将得到回复。