参数资料
型号: LTC2240CUP-10#TRPBF
厂商: Linear Technology
文件页数: 10/28页
文件大小: 0K
描述: IC ADC 10BIT 170MSPS 64-QFN
标准包装: 2,000
位数: 10
采样率(每秒): 170M
数据接口: 并联
转换器数目: 1
功率耗散(最大): 638mW
电压电源: 单电源
工作温度: 0°C ~ 70°C
安装类型: 表面贴装
封装/外壳: 64-WFQFN 裸露焊盘
供应商设备封装: 64-QFN(9x9)
包装: 带卷 (TR)
输入数目和类型: 1 个差分,双极
LTC2240-10
18
224010fb
APPLICATIONS INFORMATION
Other voltage ranges in between the pin selectable ranges
can be programmed with two external resistors as shown
in Figure 10. An external reference can be used by ap-
plying its output directly or through a resistor divider to
SENSE. It is not recommended to drive the SENSE pin
with a logic device. The SENSE pin should be tied to the
appropriate level as close to the converter as possible. If
the SENSE pin is driven externally, it should be bypassed
to ground as close to the device as possible with a 1μF
ceramic capacitor.
Input Range
The input range can be set based on the application.
The 2V input range will provide the best signal-to-noise
performance while maintaining excellent SFDR. The 1V
input range will have better SFDR performance, but the
SNR will degrade by 1.7dB. See the Typical Performance
Characteristics section.
Driving the Encode Inputs
The noise performance of the LTC2240-10 can depend
on the encode signal quality as much as on the analog
input. The ENC+/ENCinputs are intended to be driven
differentially, primarily for noise immunity from com-
mon mode noise sources. Each input is biased through
a 4.8k resistor to a 1.5V bias. The bias resistors set the
DC operating point for transformer coupled drive circuits
and can set the logic threshold for single-ended drive
circuits.
Any noise present on the encode signal will result in ad-
ditional aperture jitter that will be RMS summed with the
inherent ADC aperture jitter.
In applications where jitter is critical (high input frequen-
cies) take the following into consideration:
1. Differential drive should be used.
2. Use as large an amplitude as possible; if transformer
coupled use a higher turns ratio to increase the ampli-
tude.
3. If the ADC is clocked with a sinusoidal signal, lter the
encode signal to reduce wideband noise.
4. Balance the capacitance and series resistance at both
encode inputs so that any coupled noise will appear at both
inputs as common mode noise. The encode inputs have a
common mode range of 1.2V to 2.0V. Each input may be
driven from ground to VDD for single-ended drive.
Figure 9. Equivalent Reference Circuit
Figure 10. 1.5V Range ADC
VCM
REFHA
REFLB
SENSE
TIE TO VDD FOR 2V RANGE;
TIE TO VCM FOR 1V RANGE;
RANGE = 2 VSENSE FOR
0.5V < VSENSE < 1V
1.25V
REFLA
REFHB
2.2μF
INTERNAL ADC
HIGH REFERENCE
BUFFER
0.1μF
224010 F09
LTC2240-10
DIFF AMP
1μF
0.1μF
INTERNAL ADC
LOW REFERENCE
1.25V BANDGAP
REFERENCE
1V
0.5V
RANGE
DETECT
AND
CONTROL
VCM
SENSE
1.25V
2.2μF
8k
12k
0.75V
1μF
224010 F10
LTC2240-10
相关PDF资料
PDF描述
MS27497E16F35S CONN RCPT 55POS WALL MNT W/SCKT
IDT72V05L35J8 IC FIFO ASYNCH 4096X18 32PLCC
AD7892AN-2 IC ADC 12BIT LP 500KSPS 24-DIP
ADM207AN IC TXRX RS232 5DVR/3REC 24DIP
IDT72V211L20PF IC FIFO SYNC 512X9 20NS 32-TQFP
相关代理商/技术参数
参数描述
LTC2240CUP-12 制造商:LINER 制造商全称:Linear Technology 功能描述:12-Bit, 170Msps ADC
LTC2240CUP-12#PBF 功能描述:IC ADC 12BIT 170MSPS 64-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率(每秒):83k 数据接口:串行,并联 转换器数目:1 功率耗散(最大):95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP(0.600",15.24mm) 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端,双极
LTC2240CUP-12#TRPBF 功能描述:IC ADC 12BIT 170MSPS 64-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率(每秒):83k 数据接口:串行,并联 转换器数目:1 功率耗散(最大):95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP(0.600",15.24mm) 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端,双极
LTC2240CUP-12-PBF 制造商:LINER 制造商全称:Linear Technology 功能描述:12-Bit, 170Msps ADC
LTC2240CUP-12-TR 制造商:LINER 制造商全称:Linear Technology 功能描述:12-Bit, 170Msps ADC