- 您现在的位置：买卖IC网 > PDF目录39416 > LTC2265CUJ-12#PBF (LINEAR TECHNOLOGY CORP) PROPRIETARY METHOD ADC, QCC40 PDF资料下载
参数资料
| 型号： | LTC2265CUJ-12#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | ADC |
| 英文描述： | PROPRIETARY METHOD ADC, QCC40 |
| 封装： | 6 X 6 MM, LEAD FREE, PLASTIC, QFN-40 |
| 文件页数： | 19/34页 |
| 文件大小： | 1231K |
| 代理商： | LTC2265CUJ-12#PBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
26
22654312fb
LTC2265-12/
LTC2264-12/LTC2263-12
APPLICATIONS INFORMATION
Serial Programming Mode
To use the serial programming mode, PAR/SER should be
tied to ground. The CS, SCK, SDI and SDO pins become
a serial interface that program the A/D mode control
registers. Data is written to a register with a 16-bit serial
word. Data can also be read back from a register to verify
its contents.
Serial data transfer starts when CS is taken low. The data
on the SDI pin is latched at the first 16 rising edges of
SCK. Any SCK rising edges after the first 16 are ignored.
The data transfer ends when CS is taken high again.
The first bit of the 16-bit input word is the R/W bit. The
next seven bits are the address of the register (A6:A0).
The final eight bits are the register data (D7:D0).
If the R/W bit is low, the serial data (D7:D0) will be written
to the register set by the address bits (A6:A0). If the R/W
bit is high, data in the register set by the address bits (A6:
Table 4. Serial Programming Mode Register Map (PAR/SER = GND)
REGISTER A0: RESET REGISTER (ADDRESS 00h)
D7
D6
D5
D4
D3
D2
D1
D0
RESET
X
Bit 7
RESET
Software Reset Bit
0 = Not Used
1 = Software Reset. All Mode Control Registers Are Reset to 00h. The ADC is momentarily placed in SLEEP mode.
This Bit Is Automatically Set Back to Zero at the End of the SPI Write Command.
The Reset Register is Write Only
Bits 6-0
Unused, Don’t Care Bits.
REGISTER A1: FORMAT AND POWER-DOWN REGISTER (ADDRESS 01h)
D7
D6
D5
D4
D3
D2
D1
D0
DCSOFF
RAND
TWOSCOMP
SLEEP
NAP_2
X
NAP_1
Bit 7
DCSOFF
Clock Duty Cycle Stabilizer Bit
0 = Clock Duty Cycle Stabilizer On
1 = Clock Duty Cycle Stabilizer Off. This is Not Recommended.
Bit 6
RAND
Data Output Randomizer Mode Control Bit
0 = Data Output Randomizer Mode Off
1 = Data Output Randomizer Mode On
Bit 5
TWOSCOMP
Two’s Complement Mode Control Bit
0 = Offset Binary Data Format
1 = Two’s Complement Data Format
Bits 4, 3, 0
SLEEP: NAP_2: NAP_1
Sleep/Nap Mode Control Bits
000 = Normal Operation
0X1 = Channel 1 in Nap Mode
01X = Channel 2 in Nap Mode
1XX = Sleep Mode. Both Channels are disabled
Note: Any Combination of Channels Can Be Placed in Nap Mode.
Bits 1, 2
Unused, Don’t Care Bit
A0) will be read back on the SDO pin (see the Timing Dia-
grams section). During a readback command the register
is not updated and data on SDI is ignored.
The SDO pin is an open-drain output that pulls to ground
witha200impedance.Ifregisterdataisreadbackthrough
SDO, an external 2k pull-up resistor is required. If serial
data is only written and readback is not needed, then SDO
can be left floating and no pull-up resistor is needed. Table
4 shows a map of the mode control registers.
Software Reset
If serial programming is used, the mode control registers
should be programmed as soon as possible after the power
supplies turn on and are stable. The first serial command
mustbeasoftwareresetwhichwillresetallregisterdatabits
to logic 0. To perform a software reset, bit D7 in the reset
register is written with a logic 1. After the reset SPI write
commandiscomplete,bitD7isautomaticallysetbacktozero.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2263IUJ-12#PBF | PROPRIETARY METHOD ADC, QCC40 |
| LTC2264IUJ-12#TRPBF | PROPRIETARY METHOD ADC, QCC40 |
| LTC2272CUJ#TR | 1-CH 16-BIT PROPRIETARY METHOD ADC, SERIAL ACCESS, PQCC40 |
| LTC2272IUJ | 1-CH 16-BIT PROPRIETARY METHOD ADC, SERIAL ACCESS, PQCC40 |
| LTC2273CUJ#TR | 1-CH 16-BIT PROPRIETARY METHOD ADC, SERIAL ACCESS, PQCC40 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2265CUJ-12TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:12-Bit, 65Msps/40Msps/25Msps Low Power Dual ADCs |
| LTC2265CUJ-14 | 制造商:LINER 制造商全称:Linear Technology 功能描述:14-Bit, 65Msps/40Msps/25Msps Low Power Dual ADCs |
| LTC2265CUJ-14#PBF | 功能描述:IC ADC 14BIT SER/PAR 65M 40-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| LTC2265CUJ-14#TRPBF | 功能描述:IC ADC 14BIT SER/PAR 65M 40-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC2265CUJ-14PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:14-Bit, 65Msps/40Msps/25Msps Low Power Dual ADCs |
发布紧急采购，3分钟左右您将得到回复。