- 您现在的位置：买卖IC网 > PDF目录10531 > LTC2280IUP#PBF (Linear Technology)IC ADC DUAL 10BIT 105MSPS 64-QFN PDF资料下载
参数资料
| 型号： | LTC2280IUP#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC DUAL 10BIT 105MSPS 64-QFN |
| 标准包装： | 40 |
| 位数： | 10 |
| 采样率（每秒）： | 105M |
| 数据接口： | 并联 |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 630mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-WFQFN 裸露焊盘 |
| 供应商设备封装： | 64-QFN（9x9） |
| 包装： | 管件 |
| 输入数目和类型： | 2 个单端，双极; 2 个差分, 双极 |
| 产品目录页面： | 1349 (CN2011-ZH PDF) |
LTC2280
19
2280fa
APPLICATIO S I FOR ATIO
WU
U
ceramic capacitor is recommended. The large 2.2
F ca-
pacitor between REFH and REFL can be somewhat further
away. The traces connecting the pins and bypass capaci-
tors must be kept short and should be made as wide as
possible.
The LTC2280 differential inputs should run parallel and
close to each other. The input traces should be as short as
possible to minimize capacitance and to minimize noise
pickup.
Heat Transfer
Most of the heat generated by the LTC2280 is transferred
from the die through the bottom-side exposed pad and
package leads onto the printed circuit board. For good
electrical and thermal performance, the exposed pad
should be soldered to a large grounded pad on the PC
board. It is critical that all ground pins are connected to a
ground plane of sufficient area.
Clock Sources for Undersampling
Undersampling raises the bar on the clock source and the
higher the input frequency, the greater the sensitivity to
clock jitter or phase noise. A clock source that degrades
SNR of a full-scale signal by 1dB at 70MHz will degrade
SNR by 3dB at 140MHz, and 4.5dB at 190MHz.
In cases where absolute clock frequency accuracy is
relatively unimportant and only a single ADC is required,
a 3V canned oscillator from vendors such as Saronix or
Vectron can be placed close to the ADC and simply
connected directly to the ADC. If there is any distance to
the ADC, some source termination to reduce ringing that
may occur even over a fraction of an inch is advisable. You
must not allow the clock to overshoot the supplies or
performance will suffer. Do not filter the clock signal with
a narrow band filter unless you have a sinusoidal clock
source, as the rise and fall time artifacts present in typical
digital clock signals will be translated into phase noise.
The lowest phase noise oscillators have single-ended
sinusoidal outputs, and for these devices the use of a filter
close to the ADC may be beneficial. This filter should be
close to the ADC to both reduce roundtrip reflection times,
as well as reduce the susceptibility of the traces between
the filter and the ADC. If you are sensitive to close-in phase
noise, the power supply for oscillators and any buffers
must be very stable, or propagation delay variation with
supply will translate into phase noise. Even though these
clock sources may be regarded as digital devices, do not
operate them on a digital supply. If your clock is also used
to drive digital devices such as an FPGA, you should locate
the oscillator, and any clock fan-out devices close to the
ADC, and give the routing to the ADC precedence. The
clock signals to the FPGA should have series termination
at the source to prevent high frequency noise from the
FPGA disturbing the substrate of the clock fan-out device.
If you use an FPGA as a programmable divider, you must
re-time the signal using the original oscillator, and the re-
timing flip-flop as well as the oscillator should be close to
the ADC, and powered with a very quiet supply.
For cases where there are multiple ADCs, or where the
clock source originates some distance away, differential
clock distribution is advisable. This is advisable both from
the perspective of EMI, but also to avoid receiving noise
from digital sources both radiated, as well as propagated
in the waveguides that exist between the layers of multi-
layer PCBs.
The differential pairs must be close together, and dis-
tanced from other signals. The differential pair should be
guarded on both sides with copper distanced at least 3x
the distance between the traces, and grounded with vias
no more than 1/4 inch apart.
相关PDF资料 |
PDF描述 |
|---|---|
| PT06A-14-5P | CONN PLUG 5 POS STRAIGHT W/PINS |
| TAS5615DKDR | IC AMP AUDIO 160W STER D 44HSSOP |
| AD7863ARSZ-3 | IC ADC 14BIT DUAL 2CHAN 28SSOP |
| MS3102E24-24P | CONN RCPT 16POS BOX MNT W/PINS |
| AD7863ARSZ-10 | IC ADC 14BIT DUAL 2CHAN 28SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2280UP | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual 10-Bit, 105Msps Low Noise 3V ADC |
| LTC2281 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual 10-Bit, 125Msps Low Power 3V ADC |
| LTC2281CUP | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual 10-Bit, 125Msps Low Power 3V ADC |
| LTC2281CUP#PBF | 功能描述:IC ADC DUAL 10BIT 125MSPS 64QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC2281CUP#TRPBF | 功能描述:IC ADC DUAL 10BIT 125MSPS 64QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。