- 您现在的位置：买卖IC网 > PDF目录10672 > LTC2440IGN#PBF (Linear Technology)IC ADC DIFFER 24-BIT HS 16-SSOP PDF资料下载
参数资料
| 型号： | LTC2440IGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 5/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC DIFFER 24-BIT HS 16-SSOP |
| 标准包装： | 100 |
| 位数： | 24 |
| 采样率（每秒）： | 3.5k |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 40mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，双极 |
| 产品目录页面： | 1348 (CN2011-ZH PDF) |
| 配用： | DC570A-ND - BOARD DELTA SIGMA ADC LTC2440 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC2440
13
2440fd
APPLICATIONS INFORMATION
Chip Select Input (CS)
The active LOW chip select, CS (Pin 11), is used to test the
conversion status and to enable the data output transfer
as described in the previous sections.
In addition, the CS signal can be used to trigger a new con-
version cycle before the entire serial data transfer has been
completed. The LTC2440 will abort any serial data transfer
in progress and start a new conversion cycle anytime a
LOW-to-HIGH transition is detected at the CS pin after the
converter has entered the data output state (i.e., after the
fth falling edge of SCK occurs with CS = LOW).
Serial Data Input (SDI)—Logic Level Speed Selection
The serial data input (SDI, Pin 7) is used to select the
speed/resolution of the LTC2440. A simple 2-speed control
is selectable by either driving SDI HIGH or LOW. If SDI
is grounded (pin compatible with LTC2410) the device
outputs data at 880Hz with 21 bits effective resolution. By
tying SDI HIGH, the converter enters the ultralow noise
mode (200nVRMS) with simultaneous 50/60Hz rejection at
6.9Hz output rate. SDI may be driven logic HIGH or LOW
anytime during the conversion or sleep state in order to
change the speed/resolution. The conversion immediately
following the data output cycle will be valid and performed
at the newly selected output rate/resolution.
Changing SDI logic state during the data output cycle
should be avoided as speed resolution other than 6.9Hz
or 880Hz may be selected. For example, if SDI is changed
from logic 0 to logic 1 after the second rising edge of SCK,
the conversion rate will change from 880Hz to 55Hz (the
following values are listed in Table 3: OSR4 = 0, OSR3 = 0,
OSR2 = 1, OSR1 = 1 and OSR0 = 1). If SDI remains HIGH,
the conversion rate will switch to the desired 6.9Hz speed
immediately following the conversion at 55Hz. The 55Hz
rate conversion cycle will be a valid result as well as the
rst 6.9Hz result. On the other hand, if SDI is changed to a
1 anytime before the rst rising edge of SCK, the following
conversion rate will become 6.9Hz. If SDI is changed to
a 1 after the 5th rising edge of SCK, the next conversion
will remain 880Hz while all subsequent conversions will
be at 6.9Hz.
Serial Data Input (SDI)—Serial Input Speed Selection
SDI may also be programmed by a serial input data
stream under control of SCK during the data output cycle,
see Figure 4. One of ten speed/resolution ranges (from
6.9Hz/200nVRMSto3.5kHz/21μVRMS)maybeselected,see
Table 3. The conversion following a new selection is valid
and performed at the newly selected speed/resolution.
BUSY
The BUSY output (Pin 15) is used to monitor the state of
conversion, data output and sleep cycle. While the part is
converting, the BUSY pin is HIGH. Once the conversion is
complete, BUSY goes LOW indicating the conversion is
complete and data out is ready. The part now enters the
LOW power sleep state. BUSY remains LOW while data is
shifted out of the device. It goes HIGH at the conclusion
of the data output cycle indicating a new conversion has
begun. This rising edge may be used to ag the comple-
tion of the data read cycle.
SERIAL INTERFACE TIMING MODES
The LTC2440’s 2-wire, 3-wire or 4-wire interface is SPI
and MICROWIRE compatible. This interface offers several
exible modes of operation. These include internal/external
serial clock, 2-wire or 3-wire I/O, single cycle conversion
and autostart. The following sections describe each of
these serial interface timing modes in detail. In all these
cases, the converter can use the internal oscillator (fO =
LOW) or an external oscillator connected to the fO pin.
See Table 4 for a summary.
External Serial Clock, Single Cycle Operation
(SPI/MICROWIRE Compatible)
This timing mode uses an external serial clock to shift
out the conversion result and a CS signal to monitor and
control the state of the conversion cycle, see Figure 5.
The serial clock mode is selected by the EXT pin. To select
the external serial clock mode, EXT must be tied low.
The serial data output pin (SDO) is Hi-Z as long as CS is
HIGH. At any time during the conversion cycle, CS may be
pulled LOW in order to monitor the state of the converter.
While CS is pulled LOW, EOC is output to the SDO pin.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B1T-MX-F1 | CONVERTER MOD DC/DC 6.5V 75W |
| VE-J5K-MY-F4 | CONVERTER MOD DC/DC 40V 50W |
| DS90CR217MTD/NOPB | IC TXRX 21BIT CHAN LINK 48TSSOP |
| CS5364-CQZ | IC ADC 4CH 114DB 216KHZ 48-LQFP |
| VE-2WR-IX-B1 | CONVERTER MOD DC/DC 7.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2442CG | 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 8ksps 24-bit Serial 36-Pin SSOP |
| LTC2442CG#PBF | 功能描述:IC ADC 24BIT 4CH 36-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2442CG#TRPBF | 功能描述:IC ADC 24BIT 250MSPS 36-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2442CGPBF | 制造商:Linear Technology 功能描述:ADC 8ksps 24-Bit Serial SSOP36 |
| LTC2442IG#PBF | 功能描述:IC ADC 24BIT 4CH 36-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。