- 您现在的位置：买卖IC网 > PDF目录10667 > LTC2446IUHF#PBF (Linear Technology)IC ADC 24BIT 8CH HI SPEED 38QFN PDF资料下载
参数资料
| 型号： | LTC2446IUHF#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 19/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT 8CH HI SPEED 38QFN |
| 标准包装： | 52 |
| 位数： | 24 |
| 采样率（每秒）： | 8k |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 40mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 管件 |
| 输入数目和类型： | 8 个单端，双极；4 个差分，双极 |
| 产品目录页面： | 1348 (CN2011-ZH PDF) |
| 配用： | DC847A-ND - BOARD DELTA SIGMA ADC LTC2446 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC2446/LTC2447
26
24467fa
APPLICATIO S I FOR ATIO
WU
UU
Figure 18a is a standard 350
,voltageexcitedstraingauge
with sense wires for the excitation voltage. REF01+ and
REF01– sense the excitation voltage at the gauge, compen-
sating for voltage drop along the high current excitation
supply wires. This can be a significant error, as the exci-
tation current is 14mA when excited with 5V. Reference
loading capacitors at the ADC are necessary to average the
reference current during sampling. Both ADC inputs are
always close to mid-reference, and hence close to mid-
supply when using 5V excitation.
Figure 18b is a novel way to interface the LTC2447 to a bridge
that is specified for constant current excitation. The Fujikura
FPM-120PG is a 120psig pressure sensor that is not
trimmed for absolute accuracy, but is temperature compen-
sated for low drift when excited by a constant current source.
The LTC2447’s fully differential reference allows sensing
the excitation current with a resistor in series with the bridge
excitation. Changes in ambient temperature and supply
voltage will cause the current to vary, but the LTC2447
compensates by using the current sense voltage as its
reference. The input common mode will be slightly higher
than mid-reference, but still far enough away from the
positive supply to eliminate concerns about the buffer
amplifier’s headroom.
Figure 18c is an Omega 44018 linear output thermistor. Two
fixed resistors linearize the output from the thermistors. The
recommended 5700
seriesresistorisbrokenupintotwo
2850
resistors to give a differential output centered
around mid-reference. This ensures that the buffer ampli-
fiers have enough headroom at the negative supply. Note
that the excitation is 3V, the maximum recommended by
the manufacturer to prevent self-heating errors. The
LTC2447 senses this reference voltage.
Figure 18d shows a standard 100
platinum RTD. This
circuit shows how to use the LTC2447 to make a direct
resistance measurement, where the output code is the RTD
resistance divided by the reference resistance. A 500
sense resistor allows measurement of resistance up to
250
. (A standard α = 0.00385 RTD has a resistance of
247.09
at 400°C.)
The LTC2446 multiplexes rail-to-rail inputs directly to the
ADC modulator and is suitable for low impedance resistive
sources such as 100
RTDs and 350 strain gauges that
are located close to the ADC. In applications where the
source resistance is high or the source is located more
than 5cm to 10cm from the ADC, the LTC2447 (with an
LT1368 buffer) is appropriate. The LTC2447 automatically
removes offset, drift and 1/f noise of the LT
1368. One
consideration for single supply applications is that both
ADC inputs should always be at least 100mV from the
LT1368’s supply rails. All of the applications shown in
Figure 18 are designed to keep both analog inputs far
enough away from ground and VCC so that the LT1368 can
operate on the same 5V supply as the LTC2447. Although
the LT1368 has rail-to-rail inputs and outputs, these
amplifiers still need some degree of headroom to work at
the resolution level of the LTC2447. For input signals
running rail-to-rail, the supply voltage of the LT1368 can
be increased in order to provide the extra headroom.
The LTC2446/LTC2447 reference have no such limitations
—they are truly rail-to-rail, and will even operate up to
300mV outside the supply rails. Reference terminals may
be connected directly to the ground plane or to a reference
voltage that is decoupled to the ground plane with a 1
F or
larger capacitor without any degradation of performance
provided the connection is less than 5cm from the LTC2446/
LTC2447. If the reference terminals are sensing a point
more than 5cm to 10cm away from the ADC, the reference
pins should be decoupled to the ground plane with 1
F
capacitors.
The reference terminals can also sense a resistive source
with a resistance up to 500
locatedclosetotheLTC2446/
LTC2447, however parasitic capacitance must be kept to
a minimum. If the sense point is more than 5cm from the
ADC, then it should be buffered. The LT1368 is also an
outstanding reference buffer. While offsets are not cancelled
as in the ADC input circuit, the 200mV offset and 2mV/
°C
drift will not degrade the performance of most sensors. The
LT1369 is a quad version of the LT1368, and can serve as
the input buffer for an LTC2447 and two reference buffers.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2448IUHF#PBF | IC ADC 24BIT HI SPEED 38QFN |
| LTC2447IUHF#PBF | IC ADC 24BIT 8CH HI SPEED 38QFN |
| LTC2355CMSE-14#PBF | IC ADC 14BIT 3.5MSPS 10-MSOP |
| ISL55143IRZ-T | IC COMP CMOS HS 18V 36-TQFN |
| LTC1417CGN#PBF | IC A/D CONV 14BIT SAMPLNG 16SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2447CUHF#PBF | 功能描述:IC ADC 24BIT 8CH HI SPEED 38QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2447CUHF#TRPBF | 功能描述:IC ADC 24BIT 8CH HI SPEED 38QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2447IUHF#PBF | 功能描述:IC ADC 24BIT 8CH HI SPEED 38QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2447IUHF#TRPBF | 功能描述:IC ADC 24BIT 8CH HI SPEED 38QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2448CUHF | 功能描述:IC ADC 24BIT HI SPEED 38QFN RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。