- 您现在的位置：买卖IC网 > PDF目录8559 > LTC2704CGW-16#PBF (Linear Technology)IC DAC 16BIT QUAD VOUT 44-SSOP PDF资料下载
参数资料
| 型号： | LTC2704CGW-16#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 3/22页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT QUAD VOUT 44-SSOP |
| 产品培训模块： | LTC275x 18-Bit DAC |
| 标准包装： | 27 |
| 设置时间： | 10µs |
| 位数： | 16 |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 4 |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-BSOP（0.295"，7.50mm 宽） |
| 供应商设备封装： | 44-SSOP |
| 包装： | 管件 |
| 输出数目和类型： | 4 电压，单极；4 电压，双极 |
| 采样率（每秒）： | * |
| 配用： | DC752A-B-ND - BOARD DAC LTC2704-16 |
LTC2704
11
2704fd
SERIAL INTERFACE
When the CS/LD pin is taken low, the data on the SDI pin
is loaded into the shift register on the rising edge of the
clock signal (SCK pin). The minimum (24-bit wide) loading
sequence required for the LTC2704 is a 4-bit command
word (C3 C2 C1 C0), followed by a 4-bit address word
(A3 A2 A1 A0) and 16 data (span or code) bits, MSB
rst. Figure 1 shows the SDI input word syntax to use
when writing a code or span. If a 32-bit input sequence is
needed, the rst eight bits must be zeros, followed by the
same sequence as for a 24-bit wide input. Figure 2 shows
the input and readback sequences for both 24-bit and
32-bit operations.
When CS/LD is low, the Serial Readback Output (SRO)
pin is an active output. The readback data begins after
the command (C3-C0) and address (A3-A0) words have
been shifted into SDI. For a 24-bit load sequence, the 16
readback bits are shifted out on the falling edges of clocks
8-23, suitable for shifting into a microprocessor on the
rising edges of clocks 9-24. For a 32-bit load sequence,
add 8 to these clock cycle counts; see Figure 2b.
When CS/LD is high, the SRO pin presents a high impedance
(three-state) output. At the beginning of a load sequence,
when CS/LD is taken low, SRO outputs a logic low until
the readback data begins.
When the asynchronous load pin, LDAC, is taken low, all
DACs are updated with code and span data (data in B1
buffers is copied into B2 buffers). CS/LD must be high
during this operation. The use of LDAC is functionally
identical to the “Update B1→B2” commands.
The codes for the command word (C3-C0) are dened in
Table 1; Table 2 denes the codes for the address word
(A3-A0).
READBACK
Each DAC has two pairs of double-buffered digital regis-
ters, one pair for DAC code and the other for the output
span (four buffers per DAC). Each double-buffered pair
comprises two registers called buffer 1 (B1) and buffer
2 (B2).
B1 is the holding buffer. When data is shifted into B1 via
a write operation, DAC outputs are not affected. The con-
tents of B2 can only be changed by copying the contents
of B1 into B2 via an update operation (B1 and B2 can be
changed together, see commands 0110-1001 in Table 1).
The contents of B2 (DAC code or DAC span) directly control
the DAC output voltage or the DAC output range.
Additionally each DAC has one readback register associated
with it. When a readback command is issued to a DAC, the
contents of one of its four buffers is copied into its readback
register and serially shifted out onto the SRO pin. Figure 2
shows the loading and readback sequences. In the 16-bit
data eld (D15-D0 for the LTC2704-16, see Figure 2a) of
any write or update command, the readback pin (SRO)
shifts out the contents of the buffer which was specied in
the preceding command. This “rolling readback” mode of
operation can be used to reduce the number of operations,
since any command can be veried during succeeding
commands with no additional overhead. Table 1 shows
the location (readback pointer) of the data which will be
output from SRO during the next instruction.
For readback commands, the data is shifted out during the
readback instruction itself (on the 16 falling SCK edges im-
mediately after the last address bit is shifted in on SDI).
When programming the span of a DAC, the span bits are
the last four bits shifted in; and when checking the span of
a DAC using SRO, the span bits are likewise the last four
bits shifted out. Table 3 shows the span codes.
When span information is read back on SRO, the sleep
status of the addressed DAC is also output. The sleep status
bit, SLP, occurs sequentially just before the four span bits.
The sequence is shown in Figures 2a and 2b. See Table 4
for SLP codes. Note that SLP is an output bit only; sleep
is programmed by using command code 1110 along with
the desired address. Any update command, including the
use of LDAC, wakes the addressed DAC(s).
OPERATION
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2704IGW-14#PBF | IC DAC 14BIT QUAD VOUT 44-SSOP |
| AD669BNZ | IC DAC 16BIT MONO W/VREF 28-DIP |
| AD7237AQ | IC DAC 12BIT W/AMP W/BUFF 24CDIP |
| VI-26T-IV | CONVERTER MOD DC/DC 6.5V 150W |
| VI-BNP-MU-S | CONVERTER MOD DC/DC 13.8V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2704IGW-12 | 制造商:Linear Technology 功能描述:DAC 4-CH 12-bit 44-Pin SSOP W |
| LTC2704IGW-12#PBF | 功能描述:IC DAC 12BIT QUAD VOUT 44-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 设置时间:1µs 位数:8 数据接口:串行 转换器数目:8 电压电源:双 ± 功率耗散（最大）:941mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC W 包装:带卷 (TR) 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| LTC2704IGW-12#TRPBF | 功能描述:IC DAC 12BIT QUAD VOUT 44-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| LTC2704IGW-14#PBF | 功能描述:IC DAC 14BIT QUAD VOUT 44-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 设置时间:1µs 位数:8 数据接口:串行 转换器数目:8 电压电源:双 ± 功率耗散（最大）:941mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC W 包装:带卷 (TR) 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| LTC2704IGW-14#TRPBF | 功能描述:IC DAC 14BIT QUAD VOUT 44-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
发布紧急采购，3分钟左右您将得到回复。