- 您现在的位置：买卖IC网 > PDF目录2006 > LTC2752ACLX#PBF (Linear Technology)IC DAC 16BIT DUAL CUR OUT 48LQFP PDF资料下载
参数资料
| 型号： | LTC2752ACLX#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 2/24页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT DUAL CUR OUT 48LQFP |
| 标准包装： | 250 |
| 系列： | SoftSpan™ |
| 设置时间： | 2µs |
| 位数： | 16 |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 2 |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 托盘 |
| 输出数目和类型： | 2 电流，单极；2 电流，双极 |
| 采样率（每秒）： | * |
| 配用： | DC1684A-B-ND - BOARD DAC LTC2752 |
LTC2752
0
2752f
pin FuncTions
S2 (Pin 25): Span Bit 2 Input. In Manual Span mode (M-
SPAN tied to VDD), pins S0, S1 and S2 are pin-strapped
to select a single fixed output range for all DACs. These
pins should be tied to either GND or VDD even if they are
unused.
LDAC (Pin 26): Asynchronous DAC Load Input. When
LDAC is a logic low, all DACs are updated (CS/LD must
be high).
IOUT2BF, IOUT2BS (Pins 28, 29): DAC B Current Output
Complement Force and Sense Pins. Tie to ground via a
clean, low impedance path. These pins may be used with
a precision ground buffer amp as a Kelvin sensing pair
(see the Typical Applications section).
RINB(Pins31,32):InputResistorfortheExternalReference
Inverting Amplifier. The 20k input resistor is connected
internally from RINB to RCOMB. For normal operation tie
RINB to the external positive reference voltage (see Typical
Applications). Either or both of these precision matched
resistor sets (each set comprising RINX, RCOMX and REFX)
may be used to invert positive references to provide the
negative voltages needed by the DACs. Typically 5V; ac-
cepts up to ±15V. Pins 31 and 32 are internally shorted
together.
GEADJB (Pin 33): Gain Adjust Pin for DAC B. This control
pin can be used to null gain error or to compensate for
reference errors. The gain change expressed in LSB is
the same for any output range. See System Offset and
Gain Adjustments in the Operation section. Tie to ground
if not used.
RCOMB (Pin 34): Virtual Ground Point for the DAC B Ref-
erence Amplifier Inverting Resistors. The 20k reference
inverting resistors are connected internally from RINB to
RCOMB and from RCOMB to REFB, respectively (see Block
Diagram). For normal operation tie RCOMB to the negative
input of the external reference inverting amplifier (see
Typical Applications).
REFB (Pins 35, 36): Feedback Resistor for the DAC B
Reference Inverting Amplifier, and Reference Input for
DAC B. The 20k feedback resistor is connected internally
from REFB to RCOMB. For normal operation tie this pin to
the output of the DAC B reference inverting amplifier (see
Typical Applications). Typically –5V; accepts up to ±15V.
Pins 35 and 36 are internally shorted together.
ROFSB (Pins 37, 38): Bipolar Offset Resistor for DAC B.
These pins provide the translation of the output voltage
range for bipolar spans. Accepts up to ±15V; for normal
operation tie to the positive reference voltage at RINB (Pins
31, 32). Pins 37 and 38 are internally shorted together.
RFBB (Pins 39, 40): DAC B Feedback Resistor. For normal
operation tie to the output of the I/V converter amplifier for
DAC B (see Typical Applications). The DAC output current
fromIOUT1BflowsthroughthefeedbackresistortotheRFBB
pins. Pins 39 and 40 are internally shorted together.
IOUT1B (Pin 41): DAC B Current Output. This pin is a virtual
ground when the DAC is operating and should reside at
0V. For normal operation tie to the negative input of the I/V
converter amplifier for DAC B (see Typical Applications).
VOSADJB (Pin 42): DAC B Offset Adjust Pin. This voltage
controlpincanbeusedtonullunipolaroffsetorbipolarzero
error. The offset change expressed in LSB is the same for
anyoutputrange.SeeSystemOffsetandGainAdjustments
in the Operation section. Tie to ground if not used.
VOSADJA (Pin 43): DAC A Offset Adjust Pin. This voltage
controlpincanbeusedtonullunipolaroffsetorbipolarzero
error. The offset change expressed in LSB is the same for
anyoutputrange.SeeSystemOffsetandGainAdjustments
in the Operation section. Tie to ground if not used.
IOUT1A (Pin 44): DAC A Current Output. This pin is a virtual
ground when the DAC is operating and should reside at
0V. For normal operation tie to the negative input of the I/V
converter amplifier for DAC A (see Typical Applications).
RFBA (Pins 45, 46): DAC A Feedback Resistor. For normal
operation tie to the output of the I/V converter amplifier for
DAC A (see Typical Applications). The DAC output current
fromIOUT1AflowsthroughthefeedbackresistortotheRFBA
pins. Pins 45 and 46 are internally shorted together.
ROFSA (Pins 47, 48): Bipolar Offset Resistor for DAC A.
This pin provides the translation of the output voltage
range for bipolar spans. Accepts up to ±15V; for normal
operation tie to the positive reference voltage at RINA (Pins
5, 6). Pins 47 and 48 are internally shorted together.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2753AIUK-16#TRPBF | IC DAC 16BIT DUAL 48-QFN |
| LTC2754AIUKG-16#PBF | IC DAC 16BIT QUAD IOUT 52-QFN |
| LTC2755AIUP-16#PBF | IC DAC 16BIT CUR OUT 64-QFN |
| LTC2757ACLX#PBF | IC DAC 18BIT PAR 48LQFP |
| LTC2758AILX#PBF | IC DAC 18BIT SPI/SRL 48-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2752AILX#PBF | 功能描述:IC DAC 16BIT DUAL CUR OUT 48LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:SoftSpan™ 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| LTC2752BCLX#PBF | 功能描述:IC DAC 16BIT DUAL CUR OUT 48LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:SoftSpan™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 设置时间:4µs 位数:12 数据接口:串行 转换器数目:2 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-uMAX 包装:管件 输出数目和类型:2 电压，单极 采样率（每秒）:* 产品目录页面:1398 (CN2011-ZH PDF) |
| LTC2752BILX#PBF | 功能描述:IC DAC 16BIT DUAL CUR OUT 48LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:SoftSpan™ 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| LTC2753ACUK-16#PBF | 功能描述:IC DAC 16BIT DUAL 48-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:SoftSpan™ 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| LTC2753ACUK-16#TRPBF | 功能描述:IC DAC 16BIT DUAL 48-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:SoftSpan™ 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
发布紧急采购，3分钟左右您将得到回复。