- 您现在的位置：买卖IC网 > PDF目录15358 > LTC2919IMS-2.5#TRPBF (Linear Technology)IC MONITOR PREC 2.5V 10-MSOP PDF资料下载
参数资料
| 型号： | LTC2919IMS-2.5#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/16页 |
| 文件大小： | 0K |
| 描述： | IC MONITOR PREC 2.5V 10-MSOP |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 3 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 2.213V，可调，可调 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 带卷 (TR) |
LTC2919
APPLICATIO S I FOR ATIO
If the user wishes to avoid having an external capacitor,
the TMR pin should be tied to ground, switching the part
to an internal 200ms timer.
If the user requires a shorter timeout than 400μs, or
wishes to perform application-speci?c processing of the
reset output, the part may be put in comparator mode by
tying the TMR pin to V CC . In comparator mode, the timer
is bypassed and comparator outputs go straight to the
reset output.
The current required to hold TMR at ground or V CC is
about 2.2μA. To force the pin from the ?oating state to
ground or V CC may require as much as 100μA during the
transition.
When the part is in comparator mode, one of the two
means of preventing false reset has been removed, so
a small amount of one-sided hysteresis is added to the
inputs to prevent oscillation as the monitored voltage
passes through the threshold. This hysteresis is such
that the valid-to-invalid transition threshold is unchanged,
but the invalid-to-valid threshold is moved by about
0.7%. Thus, when the ADJ input polarity is positive,
the threshold voltage is 500mV nominal when the in-
put is above 500mV. As soon as the input drops below
500mV, the threshold moves up to 503.5mV nominal.
Conversely, when con?gured as a negative-polarity input,
the threshold is 500mV when the input is below 500mV,
and switches to 496.5mV when the input goes above
500mV.
The comparator mode feature is enabled by directly short-
ing the TMR pin to the V CC pin. Connecting the pin to any
other voltage may have unpredictable results.
Selecting the Reset Timing Capacitor
Maximum length of the reset timeout is limited by the
ability of the part to charge a large capacitor on start-up.
Initially, with a large (discharged) capacitor on the TMR
pin, the part will assume it is in internal timer mode (since
the pin voltage will be at ground). If the 2.2μA ?owing
out of the TMR pin does not charge the capacitor to the
ground-sense threshold within the ?rst 200ms after sup-
plies become good, the internal timer cycle will complete
and RST will go high too soon.
This imposes a practical limit of 1μF (9 second timeout) if
the length of timeout during power-up needs to be longer
than 200ms. If the power-up timeout is not important,
larger capacitors may be used, subject to the limitation
that the capacitor leakage current must not exceed 500nA,
or the function of the timer will be impaired.
Output Pins Characteristics
The DC characteristics of the OUT1, OUT2 and RST pull-
down strength are shown in the Typical Performance
Characteristics section. OUT1, OUT2 and RST are open-
drain pins and thus require external pull-up resistors to
the logic supply. They may be pulled above V CC , providing
the absolute maximum rating of the pin are observed.
As noted in the discussion of power up and power down,
the circuits that drive OUT1, OUT2 and RST are powered
by V CC . During a fault condition, V CC of at least 0.5V
guarantees a V OL of 0.15V.
The open-drain nature of the RST pin allows for wired-OR
connection of several LTC2919s to monitor more than two
supplies (see Typical Applications). Other logic with open-
drain outputs may also connect to the RST line, allowing
other logic-determined conditions to issue a reset.
Connecting a capacitor, C TMR , between the TMR pin and
ground sets the reset timeout, t RST . The following formula
approximates the value of capacitor needed for a particular
timeout:
C TMR = t RST ? 110 [pF/ms]
Leaving the TMR pin open with no external capacitor
generates a reset timeout of approximately 400μs.
2919f
13
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2901-3IGN#PBF | IC MONITOR QUAD SUPP PROG 16SSOP |
| ESRL560M0ER | CAP ALUM 56UF 2.5V 20% SMD |
| LTC2901-1IGN#TRPBF | IC MONITOR SUPPLY QUAD 16-SSOP |
| VI-21K-EW-F3 | CONVERTER MOD DC/DC 40V 100W |
| LTC2901-1IGN#TR | IC MONITOR SUPPLY QUAD 16-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2919IMS-3.3#PBF | 功能描述:IC MONITOR PREC 3.3V 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC2919IMS-3.3#TRPBF | 功能描述:IC MONITOR PREC 3.3V 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC2919IMS-5#PBF | 功能描述:IC MONITOR PREC 5V 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC2919IMS-5#TRPBF | 功能描述:IC MONITOR PREC 5V 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC2920-1CS5 | 制造商:Linear Technology 功能描述:Volt Supervisor Controller 5-Pin TSOT-23 |
发布紧急采购，3分钟左右您将得到回复。