- 您现在的位置：买卖IC网 > PDF目录69007 > LTC2941IDCB-1#TRMPBF (LINEAR TECHNOLOGY CORP) POWER SUPPLY SUPPORT CKT, PDSO6 PDF资料下载
参数资料
| 型号： | LTC2941IDCB-1#TRMPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, PDSO6 |
| 封装： | 2 X 3 MM, LEAD FREE, PLASTIC, MO-229TBD, DFN-6 |
| 文件页数： | 16/16页 |
| 文件大小： | 206K |
| 代理商： | LTC2941IDCB-1#TRMPBF |
LTC2941-1
29411f
applicaTions inFormaTion
Bit A[5] is set if the LTC2941-1’s accumulated charge over-
flowsorunderflowsthecombinedtotalinregistersCandD.
Notethatthecountingprocessdoesnotrollover,butsimply
stops at FFFFh or 0000h until the direction is reversed.
The LTC2941-1 includes a battery undervoltage monitor,
whichsetsbitA1ifthelimitisexceeded.Limitsareselected
in the control register.
The undervoltage lockout (UVLO) bit A[0] is set if, dur-
ing operation, the voltage on SENSE+ drops below 2.7V
without reaching the POR level. The analog parts of the
coulomb counter are switched off while the digital register
values are retained. After recovery of the supply voltage
the coulomb counter resumes integrating with the stored
value in the accumulated charge registers (C, D) but it has
missed any charge flowing while VSENSE+ < 2.7V.
The hard coded bit A[7] of the status register enables the
host to distinguish the LTC2941-1 from the pin compat-
ible LTC2942-1, allowing the same software to be used
with both devices.
Control Register (B)
The operation of the LTC2941-1 can be controlled by
programming the control register at address 01h. Table 3
shows the organization of the 8-bit control register B[7:0]
Table 3. Control Register B
BIT NAME
OPERATION
DEFAULT
B[7:6] VBAT Alert
[11] Threshold Value = 3.0V.
[10] Threshold Value = 2.9V.
[01] Threshold Value = 2.8V.
[00] VBAT Alert Off.
[00]
B[5:3] Prescaler M Sets coulomb counter prescaling
factor M between 1 and 128.
Default is 128.
M = 2(4 B[5] + 2 B[4] + B[3]).
[111]
B[2:1] AL/CC
Configure
Configures the AL/CC pin.
[10] Alert Mode.
Alert functionality enabled.
Pin becomes logic output.
[01] Charge Complete Mode.
Pin becomes logic input and accepts
“charge complete” signal (e.g., from
a charger) to set accumulated charge
Register to FFFFh.
[00] AL/CC pin disabled.
[11] Not allowed.
[10]
B[0] Shutdown
Shut down analog section to reduce
ISUPPLY.
[0]
Power Down B[0]
Programming the last bit B[0] of the control register to 1
sets the analog parts of the LTC2941-1 in power down and
the current consumption drops typically below 1A. All
analogcircuitsaredisabledwhilethevaluesintheregisters
are retained. Note that any charge flowing while B[0] is 1
is not measured and the charge information below 1LSB
of the accumulated charge register is lost.
Alert/Charge Complete Configuration B[2:1]
The AL/CC pin is a dual function pin configured by the
control register. By setting bits B[2:1] to [10] (default) the
AL/CCpinisconfiguredasanalertpinfollowingtheSMBus
protocol. In this alert mode the AL/CC pin is a digital output
and is pulled low if one of the measured quantities exceeds
its high or low threshold or if the an overflow/underflow
occurs in the accumulated charge registers C and D. An
alert response procedure started by the master resets the
alert at the AL/CC pin. For further information see the Alert
Response Protocol section.
SettingthecontrolbitsB[2:1]to[01]configurestheAL/CC
pin as a digital input. In this mode, a high input on the
AL/CCpincommunicatestotheLTC2941-1thatthebattery
is full and the accumulated charge is set to its maximum
value FFFFh. Coulomb counting starts when the AL/CC pin
returns to low level.
If neither the alert nor the charge complete functionality
is desired, bits B[2:1] should be set to [00]. The AL/CC
pin is then disabled and should be tied to GND. Avoid set-
ting B[2:1] to [11] as it enables the alert and the charge
complete modes simultaneously.
Choosing Coulomb Counter Prescaler ‘M’ B[5:3]
To use as much of the range of the accumulated charge
register as possible the prescaler factor M is chosen based
on battery capacity QBAT:
M
Q
mAh Ah
Q
BAT
≥
=
128
2
0 085
23
16
.
M can be set to 1, 2 ,4, 8,... 128 by programming B[5:3]
of the control register as M = 2(4 B[5] + 2 B[4] + B[3]).
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2941CDCB-1#TRPBF | POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC2941IDCB-1#TRPBF | POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC2991CMS#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC2991IMS#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC2991IMS#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2942CDCB#PBF | 制造商:Linear Technology 功能描述:IC, BATTERY GAS GAUGE, LI-ION, DFN-6; Battery Management Function:Fuel Gauge; Battery Type:Li-Ion; Supply Voltage Min:2.7V; Supply Voltage Max:5.5V; Battery IC Case Style:DFN; No. of Pins:6; IC Interface Type:I2C ;RoHS Compliant: Yes |
| LTC2942CDCB#TRMPBF | 功能描述:IC FUEL/GAS GAUGE LI-ION 6DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC2942CDCB#TRPBF | 功能描述:IC FUEL/GAS GAUGE LI-ION 6DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC2942CDCB-1#PBF | 制造商:Linear Technology 功能描述:IC BATTERY FUEL GAUGE LI-ION 5.5V DFN-6 制造商:Linear Technology 功能描述:IC, BATTERY FUEL GAUGE LI-ION 5.5V DFN-6 制造商:Linear Technology 功能描述:IC, BATTERY FUEL GAUGE LI-ION 5.5V DFN-6; Battery Management Function:Fuel Gauge, Charge Controller; Battery Type:Li-Ion; Supply Voltage Min:2.7V; Supply Voltage Max:5.5V; Battery IC Case Style:DFN; No. of Pins:6 ;RoHS Compliant: Yes |
| LTC2942CDCB-1#TRMPBF | 功能描述:IC FUEL/GAS GAUGE LI-ION 1A 6DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
发布紧急采购，3分钟左右您将得到回复。