- 您现在的位置：买卖IC网 > PDF目录44989 > LTC2942IDCB#TRPBF (LINEAR TECHNOLOGY CORP) POWER SUPPLY SUPPORT CKT, PDSO6 PDF资料下载
参数资料
| 型号： | LTC2942IDCB#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, PDSO6 |
| 封装： | 2 X 3 MM, LEAD FREE, PLASTIC, MO-229, DFN-6 |
| 文件页数： | 3/18页 |
| 文件大小： | 227K |
| 代理商： | LTC2942IDCB#TRPBF |
LTC2942
11
2942fa
applicaTions inFormaTion
Choosing Coulomb Counter Prescaler M B[5:3]
If the battery capacity (QBAT) is very small compared to
the maximum current (IMAX) (QBAT < IMAX 0.1 Hours)
the prescaler value M should be changed from its default
value (128).
In these applications with a small battery but a high
maximum current, qLSB can get quite large with respect
to the battery capacity. For example, if the battery capacity
is 100mAh and the maximum current is 1A, the standard
equation leads to choosing a sense resistor value of
50mΩ, resulting in:
qLSB = 0.085mAh = 306mC
The battery capacity then corresponds to only 1176 qLSBs
and less than 2% of the accumulated charge register is
utilized.
To preserve digital resolution in this case, the LTC2942
includes a programmable prescaler. Lowering the pres-
caler factor M allows reducing qLSB to better match the
accumulated charge register to the capacity of the battery.
The prescaling factor M can be chosen between 1 and its
default value 128. The charge LSB then becomes:
qLSB =0.085mAh
50m
RSENSE
M
128
To use as much of the range of the accumulated charge
register as possible the prescaler factor M should be
chosen for a given battery capacity QBAT and a sense
resistor RSENSE as:
M
≥128
QBAT
216 0.085mAh
RSENSE
50m
M can be set to 1, 2, 4, 8, … 128 by programming B[5:3] of
thecontrolregisterasM=2(4B[5]+2B[4]+B[3]).Thedefault
value after power up is M = 128 = 27 (B[5:3] = 111).
In the above example of a 100mAh battery and an RSENSE
of 50mΩ, the prescaler should be programmed to M = 4.
The qLSBthenbecomes2.656Ahandthebatterycapacity
corresponds to roughly 37650 qLSBs.
Note that the internal digital resolution of the coulomb
counter is higher than indicated by qLSB. The digitized
chargeqINTERNALisM8timessmallerthanqLSB.qINTERNAL
is typically 299As for a 50mΩ sense resistor.
ADC Mode B[7:6]
The LTC2942 features an ADC which measures either
voltage on SENSE– (battery voltage) or temperature via
an internal temperature sensor. The reference voltage and
clock for the ADC are generated internally.
The ADC has four different modes of operation, as shown
in Table 3. These modes are controlled by bits B[7:6] of
the control register. At power-up, bits B[7:6] are set to
[00] and the ADC is in sleep mode.
A single voltage conversion is initiated by setting the bits
B[7:6] to [10]. A single temperature conversion is started
by setting bits B[7:6] to [01]. After a single voltage or
temperature conversion, the ADC resets B[7:6] to [00]
and goes to sleep.
The LTC2942 also offers an automatic scan mode where
the ADC converts voltage, then temperature, then sleeps
forapproximatelytwosecondsbeforerepeatingthevoltage
and temperature conversions. The LTC2942 is set to this
automatic mode by setting B[7:6] to [11] and stays in this
mode until B[7:6] are reprogrammed by the host.
Programming B[7:6] to [00] puts the ADC to sleep. If
control bits B[7:6] change within a conversion, the ADC
will complete the current conversion before entering the
newly selected mode.
Aconversionofeithervoltageortemperaturerequires10ms
conversion time (typical). At the end of each conversion,
the corresponding registers are updated. If the converted
quantity exceeds the values programmed in the threshold
registers, a flag is set in the status register and the AL/CC
pin is pulled low (if alert mode is enabled).
During a voltage conversion, the SENSE– pin is connected
through a small resistor to a sampling circuit with an
equivalent resistance of 2MΩ, leading to a mean input
current of I = VSENSE–/2MΩ.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2942CDCB#TRPBF | POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC2990CMS#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC2990CMS#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC2990IMS#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC2990IMS | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2943CDD#PBF | 制造商:Linear Technology 功能描述:IC GAS GAUGE MULTICELL 8DFN 制造商:Linear Technology 功能描述:BATTERY GAS GAUGE, 20V, DFN-8, Battery Management Function:Fuel Gauge, Battery Type:-, Supply Voltage Min:3.6V, Supply Voltage Max:20V, Battery IC Case Style:DFN, No. of Pins:8, IC Interface Type:I2C, SMBus, Package / Case:8-DFN , RoHS Compliant: Yes |
| LTC2943CDD#TRPBF | 制造商:Linear Technology 功能描述:BATTERY GAS GAUGE, 20V, DFN-8, Battery Management Function:Fuel Gauge, Supply Voltage Min:3.6V, Supply Voltage Max:20V, Battery IC Case Style:DFN, No. of Pins:8, IC Interface Type:I2C, SMBus, Operating Temperature Min:0C , RoHS Compliant: Yes |
| LTC2945CMS#PBF | 制造商:Linear Technology 功能描述: 制造商:Linear Technology 功能描述:IC POWER MONITOR I2C 12-MSOP 制造商:Linear Technology 功能描述:MS-System Monitor/Other, Wide Range I2C Power Monitor (SDAO) |
| LTC2945CMS#TRPBF | 制造商:Linear Technology 功能描述:IC POWER MONITOR I2C 12-MSOP 制造商:Linear Technology 功能描述:MS-System Monitor/Other, Wide Range I2C Power Monitor (SDAO) |
| LTC2945CMS-1#PBF | 制造商:Linear Technology 功能描述:I2C Power Monitor 12-Pin MSOP 制造商:Linear Technology 功能描述:IC POWER MONITOR I2C 12-MSOP |
发布紧急采购，3分钟左右您将得到回复。