- 您现在的位置：买卖IC网 > Datasheet目录338 > LTC3206EUF#TRPBF (Linear Technology)IC LED DRVR WT/RGB BCKLGT 24-QFN Datasheet资料下载
参数资料
| 型号： | LTC3206EUF#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WT/RGB BCKLGT 24-QFN |
| 标准包装： | 2,500 |
| 拓扑： | PWM，切换式电容器（充电泵） |
| 输出数： | 11 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | RGB，白色 LED |
| 频率： | 680kHz ~ 1.36MHz |
| 电源电压： | 2.7 V ~ 4.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN 裸露焊盘（4x4） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
LTC3206
APPLICATIO S I FOR ATIO
White LED Brightness Control
The White LED displays (MAIN, SUB and AUX) have 16
AVG ( I LED ) = 400 ?
0. 6V
R MS
? 2
D ? 15
individual brightness settings. The settings are exponen-
tially spaced to compensate for the nearly logarithmic
characteristic of human vision perception. The base of the
power settings is √ 2 . The off setting (0 power) is a special
case needed for shutdown.
The LTC3206 uses a subranging technique to control the
LED brightness with a combination of both DC level
control and pulse width modulation. Table 1 summarizes
the level control operation. The DC level of the LEDs will be
one of either three sub-range settings, 100%, 50% or 25%
of full scale. For example, if the full scale LED current is
programmed (via the IMS pin) to be 20mA, then the “on”
level of the LED will be either 20mA, 10mA or 5mA
respectively. The power to the LED will be the product of
the subrange (DC current) and the PWM setting. For
example, if an LED power of 2.25% is desired, then the
LTC3206 sets the sub range to 25% and the duty cycle to
8.8%. These settings are designed to optimize the effi-
ciency of the dual-mode LTC3206 power management
system while preserving LED color accuracy at low power
levels.
To achieve brightness control by purely DC means, only
the 100%, 50% or 25% power settings should be selected.
The DC current levels of the MAIN, SUB and AUX LEDs are
controlled by a precisely mirrored multiple of the current
at the I MS pin. The I MS pin servos to a fixed level of 0.6V so
the current is programmed simply by adding a resistor
from I MS to ground.
The current that flows during the “on” time will follow the
relationship:
where D is the decimal equivalent of the 4-bit digital code
programmed for the given display (0 to 15).
The PWM frequency is 1/1024 of the frequency of the
charge pump oscillator (typically 938Hz). During PWM,
the LED currents are soft-switched to minimize noise.
AUX LEDs
The AUX1 and AUX2 LEDs can be arbitrarily assigned to
either the MAIN or SUB display. Table 2 summarizes the
assignment possibilities. When an AUX pin is assigned to
a display, it will follow the power level (both DC and PWM)
set for that display.
Unused White LED Pins
The LTC3206 can power up to eight white LEDs (four for
the MAIN display, two for the SUB display and the two
flexible AUX pins), however, it is not necessary to use all
eight in each application.
Any of these LED pins can cause the LTC3206 to switch
from 1x mode to 1.5x charge pump mode if they drop out.
In fact, if an unused LED pin is left unconnected or
grounded, it will drop out and force the LTC3206 into
charge pump mode.
To avoid this problem, unused MAIN, SUB or AUX LED
pins can be disabled by connecting them to CPO. Power is
not wasted in this configuration. When the LED pin voltage
is within approximately 1V of CPO, its LED current is
switched off and only a small 10 μ A test current remains.
Figure 5 shows a block diagram of each of the MAIN, SUB
and AUX LED pins.
I LED = 400 ? S ?
0.6 V
R MS
+
1V
– +
CPO
MAIN1-MAIN4
where S is the subrange for the given power setting (it will
be either 25%, 50% or 100%, see Table 1) and R MS is the
value of the resistor at the I MS pin.
ENABLE
–
SUB1, SUB2, AUX1, AUX2
10 μ A
The average LED current (LED power level) will follow the
relationship:
I LED
3206 F05
Figure 5. Internal MAIN, SUB and AUX LED Disable Circuit
3206f
10
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3207EUF-1#TRPBF | IC LED DRIVR QVGA DISPLAY 24-QFN |
| LTC3208EUH#TRPBF | IC LED DRIVR QVGA DISPLAY 32-QFN |
| LTC3209EUF-2#TRPBF | IC LED DRIVR QVGA DISPLAY 20-QFN |
| LTC3210EPD-1#TRPBF | IC LED DRVR WHITE BCKLT 16-UTQFN |
| LTC3210EUD#TRPBF | IC LED DRIVR WHITE BCKLGT 16-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3207 | 制造商:LINER 制造商全称:Linear Technology 功能描述:600mA Universal Multi-Output LED/CAM Driver |
| LTC3207-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:600mA Universal Multi-Output LED/CAM Driver |
| LTC3207EUF#PBF | 功能描述:IC LED DRIVR QVGA DISPLAY 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LTC3207EUF#TRPBF | 功能描述:IC LED DRIVR QVGA DISPLAY 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LTC3207EUF-1#PBF | 功能描述:IC LED DRIVR QVGA DISPLAY 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
发布紧急采购，3分钟左右您将得到回复。