- 您现在的位置：买卖IC网 > Datasheet目录338 > LTC3206EUF#TRPBF (Linear Technology)IC LED DRVR WT/RGB BCKLGT 24-QFN Datasheet资料下载
参数资料
| 型号： | LTC3206EUF#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WT/RGB BCKLGT 24-QFN |
| 标准包装： | 2,500 |
| 拓扑： | PWM，切换式电容器（充电泵） |
| 输出数： | 11 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | RGB，白色 LED |
| 频率： | 680kHz ~ 1.36MHz |
| 电源电压： | 2.7 V ~ 4.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN 裸露焊盘（4x4） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
LTC3206
APPLICATIO S I FOR ATIO
The RED, GREEN and BLUE pins can also enable the
charge pump, however, since they each have individual
disable control they can be left floating or grounded if
unused.
RGB Illuminator Brightness Control
The RED, GREEN and BLUE LEDs can be individually set
to have a linear duty cycle ranging from 0/15 (off) to
15/15 (full on) with 1/15 increments in between. The
combination of 16 possible brightness levels gives the
RGB indicator LED a total of 4096 colors. Table 1 indicates
the decoding of the RED, GREEN and BLUE LEDs.
The full-scale currents in the RED, GREEN and BLUE LEDs
are controlled by the current at the I RGB pin in a similar
manner to those in the MAIN, SUB and AUX LEDs. The
I RGB pin also servos to 0.6V and the RGB LED currents are
a precise multiple of the I RGB current. The DC value of the
RGB display LED currents will follow the relationship:
(see Figure 3 and Table 3) determines which display
ENRGB/S controls. When bit A2 is 0, the ENRGB/S pin
controls the RGB display. If it is set to 1, ENRGB/S controls
the SUB display.
To use the ENRGB/S pin, the I 2 C port must first be
configured to the desired setting. For example, if ENRGB/S
will be used to control the SUB display, then a non-zero
code must reside in the C3-C0 nibble of the I 2 C port and bit
A2 must be set to 1 (see Table 1). Now when ENRGB/S is
high (DV CC ), the SUB display will be on with the C3-C0
setting. When ENRGB/S is low, the SUB display will be off.
If no other displays are programmed to be on, the entire
chip will be in shutdown.
Likewise, if ENRGB/S will be used to enable the RGB
display, then a non-zero code must reside in one of the
RED, GREEN or BLUE nibbles of the serial port (A4-A7 or
B0-B7), and bit A2 must be 0. Now when ENRGB/S is high
(DV CC ), the RGB display will light with the programmed
color. When ENRGB/S is low, the RGB display will be off.
,
I RED , GREENBLUE = 400
0.6 V
R RGB
If no other displays are programmed to be on, the entire
chip will be in shutdown.
where R RGB is the value of the resistor at the I RGB pin.
The average value of the current in the RED, GREEN and
BLUE LEDs will be:
D 0 . 6 V
AVG ( I RED , GREEN , BLUE ) = 400 ? ?
15 R RGB
where D is the decimal equivalent of the 4-bit digital code
programmed for the given LED(0 to 15). Table 1 summa-
rizes the RED, GREEN and BLUE LED power settings.
The RED, GREEN and BLUE LEDs are pulse width modu-
lated at a frequency of 1/240 of the frequency of the charge
pump oscillator or about 4kHz.
ENRGB/S Pin
The ENRGB/S pin can be used to enable or disable the
LTC3206 without re-accessing the I 2 C port. This might be
useful to indicate an incoming phone call without waking
the microcontroller. ENRGB/S can be software pro-
grammed as an independent control for either the RGB
If bit A2 is set to 1 (SUB display control), then ENRGB/S
will have no effect on the RGB display. Likewise, if bit A2
is set to 0 (RGB display control), then ENRGB/S will have
no effect on the SUB display.
If the ENRGB/S pin is not used, it should be connected to
DV CC . It should not be grounded or left floating.
V IN , CPO Capacitor Selection
The style and value of capacitors used with the LTC3206
determine several important parameters such as regulator
control-loop stability, output ripple and charge pump
strength. To reduce noise and ripple, it is recommended
that low equivalent series resistance (ESR) multilayer
ceramic capacitors be used on both V IN and CPO. Tanta-
lum and aluminum capacitors are not recommended be-
cause of their high ESR. The value of the capacitor on CPO
directly controls the amount of output ripple for a given
load current. Increasing the size of this capacitor will
reduce the output ripple. The peak-to-peak output ripple is
approximately given by the expression:
display or the SUB display. Control bit A2 in the serial port
V RIPPLE P-P ?
I CPO
3 f OSC ? C CPO
3206f
11
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3207EUF-1#TRPBF | IC LED DRIVR QVGA DISPLAY 24-QFN |
| LTC3208EUH#TRPBF | IC LED DRIVR QVGA DISPLAY 32-QFN |
| LTC3209EUF-2#TRPBF | IC LED DRIVR QVGA DISPLAY 20-QFN |
| LTC3210EPD-1#TRPBF | IC LED DRVR WHITE BCKLT 16-UTQFN |
| LTC3210EUD#TRPBF | IC LED DRIVR WHITE BCKLGT 16-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3207 | 制造商:LINER 制造商全称:Linear Technology 功能描述:600mA Universal Multi-Output LED/CAM Driver |
| LTC3207-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:600mA Universal Multi-Output LED/CAM Driver |
| LTC3207EUF#PBF | 功能描述:IC LED DRIVR QVGA DISPLAY 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LTC3207EUF#TRPBF | 功能描述:IC LED DRIVR QVGA DISPLAY 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LTC3207EUF-1#PBF | 功能描述:IC LED DRIVR QVGA DISPLAY 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
发布紧急采购，3分钟左右您将得到回复。