- 您现在的位置：买卖IC网 > PDF目录80057 > LTC3226EUD#PBF (LINEAR TECHNOLOGY CORP) SWITCHED CAPACITOR REGULATOR, PQCC16 PDF资料下载
参数资料
| 型号： | LTC3226EUD#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHED CAPACITOR REGULATOR, PQCC16 |
| 封装： | 3 X 3 MM, LEAD FREE, PLASTIC, MO-220WEED-2, QFN-16 |
| 文件页数： | 16/16页 |
| 文件大小： | 431K |
| 代理商： | LTC3226EUD#PBF |
LTC3226
9
3226f
OPERATION
The LTC3226 is a 2-cell series supercapacitor charger
designed to back up a Li-ion battery or any system rail
in the range of 2.5V to 5.3V. It has four principal circuit
components: a dual mode (1x/2x) charge pump with an
integrated balancer and a voltage clamp, an LDO to supply
the load current from the charge stored on the superca-
pacitor, an ideal diode controller to control the gate of the
external FET between VIN and VOUT, and a PFI comparator
todecidewhethertoactivatethechargepumptochargethe
supercapacitor stack or to activate the LDO to supply the
loadwhenVINfallsbelowanexternallyprogrammedvalue.
The LTC3226 has two modes of operation: normal and
backup. If VIN is above an externally programmable PFI
threshold voltage, the part is in normal mode in which
power flows from VIN to VOUT through the external FET
and the internal charge pump stays on to top off the
supercapacitor stack. If VIN is below this PFI threshold,
the part is in backup mode. In this mode, the internal
charge pump is turned off, the external FET is turned off
and the LDO is turned on to supply the load current from
the stored charge.
CHARGE PUMP
One of the principal circuit components of the LTC3226
is a dual mode low noise constant frequency (0.9MHz)
regulated charge pump which transfers charge from VIN
and stores it onto the supercapacitor stack at the CPO pin.
The target or termination voltage on the CPO pin is pro-
grammed by an external resistor divider using the CPO_FB
pin. The input current limit to the charger is programmed
by an external resistor between the PROG pin and ground.
ThechargepumpturnsonwhenVINexceedstheexternally
programmablePFIthreshold.Atthebeginningofthecharge
cycle when the CPO pin voltage is less than VIN, the charge
pumpisin1xmode(linearmode)inwhichthechargepump
actsasapasselementandchargesthesupercapacitorwith
a charge current that is limited by the programmed input
current limit. As the CPO voltage rises to within 200mV of
the input supply voltage, the charge pump switches to 2x
mode (doubler mode) in which the average charge current
is approximately equal to half the input current limit. As the
CPOvoltageexceedsthetargetvaluebyapproximately1%,
the charge pump switches turn off and the charge pump
enters the sleep mode. In sleep mode, most of the charge
pump control circuitry is turned off to minimize quiescent
current. As the supercapacitor discharges due to leakage
and internal quiescent current load, the CPO pin voltage
slowly drops. When the CPO pin voltage drops 1% below
the programmed voltage, the charge pump turns on to
replenish charge on the supercapacitor and the cycle con-
tinues. The charge pump can be turned off by pulling the
EN_CHG pin below 0.4V. However, by default, the charge
pump is always enabled via an internal low current pull-up
circuit if the EN_CHG pin is left floating.
Voltage Clamp
The LTC3226 charge pump is equipped with circuitry to
limit the voltage across any supercapacitor in the stack
to a maximum allowable preset voltage of 2.65V. If the
voltage across the top capacitor (VMID-VCPO) ever gets
to 2.65V before the CPO pin reaches the target voltage,
the charge pump stops charging the top of the stack via
the CPO pin, switches to 1x mode and delivers charge
directly to the bottom capacitor via the VMID pin until the
stack voltage reaches its programmed value. If the voltage
across the bottom capacitor reaches 2.65V before the
stack gets to its target value, the charge pump continues
to deliver charge to the top of the stack via the CPO pin
and a shunt regulator turns on to bleed charge off of the
bottom capacitor and prevents the VMID pin voltage from
rising any further. The shunt regulator is able to shunt the
maximumallowablechargecurrentwhichisapproximately
315mA (in 1x mode). In the event both capacitors exceed
2.65V, the charge pump enters sleep mode by turning off
most of its circuitry.
Leakage Balancer
The LTC3226 is equipped with an internal leakage balanc-
ing amplifier which servos the VMID pin voltage to exactly
half of the CPO pin voltage. However, it has limited source
(~4.5mA) and sink (~5.5mA) capability. It is designed to
handle slight mismatch of the supercapacitors due to
leakage currents; not to correct any gross mismatch due
to defects. The balancer is only active as long as the input
supply voltage is above the PFI threshold. The internal bal-
ancer eliminates the need for external balancing resistors.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3872HDDB#PBF | SWITCHING CONTROLLER, 650 kHz SWITCHING FREQ-MAX, PDSO8 |
| LVB48S | 1-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE |
| LH2540-2D4 | 2-OUTPUT AC-DC UNREG PWR SUPPLY MODULE |
| LS2320-9EPD1T | 2-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LT1021AMH-10 | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 10 V, MBCY8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3226IUD | 制造商:LINEAR 制造商全称:LINEAR 功能描述:2-Cell Supercapacitor Charger with Backup PowerPath Controller |
| LTC3226IUD#PBF | 功能描述:IC 2CELL SUPERCAP CHARGE 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:PowerPath™ 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3226IUD#TRPBF | 功能描述:IC 2CELL SUPERCAP CHARGE 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:PowerPath™ 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3230 | 制造商:LINER 制造商全称:Linear Technology 功能描述:5-LED Main/Sub Display Driver with Dual LDO |
| LTC3230EUD#PBF | 功能描述:IC LED DRIVR WHITE BCKLGT 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
发布紧急采购，3分钟左右您将得到回复。