- 您现在的位置：买卖IC网 > PDF目录14066 > LTC3404EMS8#TRPBF (Linear Technology)IC REG BUCK SYNC ADJ 0.6A 8MSOP PDF资料下载
参数资料
| 型号： | LTC3404EMS8#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 0.6A 8MSOP |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 6 V |
| 输入电压： | 2.65 V ~ 6 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 1.4MHz |
| 电流 - 输出： | 600mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-MSOP |
LTC3404
APPLICATIO S I FOR ATIO
which is below the maximum junction temperature of
125 ° C.
Note that at higher supply voltages, the junction tempera-
ture is lower due to reduced switch resistance (R DS(ON) ).
Checking Transient Response
The regulator loop response can be checked by looking at
the load transient response. Switching regulators take
several cycles to respond to a step in load current. When
a load step occurs, V OUT immediately shifts by an amount
equal to ( Δ I LOAD ? ESR), where ESR is the effective series
resistance of C OUT . Δ I LOAD also begins to charge or
discharge C OUT , which generates a feedback error signal.
The regulator loop then acts to return V OUT to its steady-
state value. During this recovery time V OUT can be moni-
tored for overshoot or ringing that would indicate a stabil-
ity problem. The internal compensation provides adequate
compensation for most applications. But if additional
compensation is required, the I TH pin can be used for
external compensation using R C , C C1 as shown in
Figure 7. (The 47pF capacitor, C C2 , is typically needed for
noise decoupling.)
A second, more severe transient is caused by switching in
loads with large (>1 μ F) supply bypass capacitors. The
discharged bypass capacitors are effectively put in parallel
with C OUT , causing a rapid drop in V OUT . No regulator can
deliver enough current to prevent this problem if the load
switch resistance is low and it is driven quickly. The only
solution is to limit the rise time of the switch drive so that
the load rise time is limited to approximately (25 ? C LOAD ).
C C2
Thus, a 10 μ F capacitor charging to 3.3V would require a
250 μ s rise time, limiting the charging current to about
130mA.
PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of the
LTC3404. These items are also illustrated graphically in
the layout diagram of Figure 7. Check the following in your
layout:
1. Are the signal and power grounds segregated? The
LTC3404 signal ground consists of the resistive
divider, the optional compensation network (R C and
C C1 ) and C C2 . The power ground consists of the (–)
plate of C IN , the (–) plate of C OUT and Pin 4 of the
LTC3404. The power ground traces should be kept
short, direct and wide. The signal ground and power
ground should converge to a common node in a star-
ground configuration.
2. Does the V FB pin connect directly to the feedback
resistors? The resistive divider R1/R2 must be con-
nected between the (+) plate of C OUT and signal ground.
3. Does the (+) plate of C IN connect to V IN as closely as
possible? This capacitor provides the AC current to the
internal power MOSFETs.
4. Keep the switching node SW away from sensitive small
signal nodes.
Design Example
As a design example, assume the LTC3404 is used in a
OPTIONAL
R C
R2
C C1
R1
1
2
3
4
LTC3404
RUN PLL LPF
I TH SYNC/MODE
V FB
GND SW
C IN
+
8
7
V IN 6
5
L1
BOLD LINES INDICATE
HIGH CURRENT PATHS
+
+ V OUT
C OUT
+
V IN
single lithium-ion battery-powered cellular phone applica-
tion. The input voltage will be operating from a maximum
of 4.2V down to about 2.7V. The load current requirement
is a maximum of 0.3A but most of the time it will be in
standby mode, requiring only 2mA. Efficiency at both low
and high load currents is important. Output voltage is
2.5V. With this information we can calculate L using
equation (1),
V OUT ? 1 ? OUT ?
–
–
3404 F07
L =
1
( ) f ( Δ I L )
? V ?
? V IN ?
(3)
Figure 7. LTC3404 Layout Diagram
3404fb
13
相关PDF资料 |
PDF描述 |
|---|---|
| ESC19DRYS-S93 | CONN EDGECARD 38POS DIP .100 SLD |
| VI-J6B-EZ | CONVERTER MOD DC/DC 95V 25W |
| 25MS74.7MEFC4X7 | CAP ALUM 4.7UF 25V 20% RADIAL |
| VI-J61-EZ | CONVERTER MOD DC/DC 12V 25W |
| ESC26DREN-S93 | CONN EDGECARD 52POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3404IMS8 | 制造商:Linear Technology 功能描述:DP-SWREG/Monolithic, 1.4MHz High Eff Synch Step-dn Reg |
| LTC3404IMS8#PBF | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3404IMS8#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3404MPMS8 | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 2.65V to 6V 8-Pin MSOP |
| LTC3404MPMS8#PBF | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。