- 您现在的位置：买卖IC网 > PDF目录1829 > LTC3409IDD#TRPBF (Linear Technology)IC REG BUCK SYNC ADJ 0.6A 8DFN PDF资料下载
参数资料
| 型号： | LTC3409IDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 0.6A 8DFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.62 V ~ 5.5 V |
| 输入电压： | 1.6 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 1.7MHz ~ 2.6MHz |
| 电流 - 输出： | 600mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-DFN-EP（3x3） |
LTC3409
APPLICATIONS INFORMATION
The basic LTC3409 application circuit is shown on the ?rst
Table 1. Representative Surface Mount Inductors
page of this data sheet. External component selection is
driven by the load requirement and begins with the selec-
tion of L followed by C IN and C OUT .
Inductor Selection
For most applications, the value of the inductor will fall
in the range of 1μH to 10μH. Its value is chosen based
on the desired ripple current. Large value inductors
lower ripple current and small value inductors result in
higher ripple currents. Higher V IN or V OUT also increases
the ripple current as shown in Equation 1. A reasonable
starting point for setting ripple current is ΔI L = 240mA
PART
NUMBER
Sumida
CDRH2D18/LD
Sumida
CDRH2D11
Sumida
CMD4D11
Murata
LQH32CN
Toko
D312F
Panasonic
ELT5KT
VALUE
(μH)
2.2
3.3
1.5
2.2
2.2
3.3
1.0
2.2
2.2
3.3
3.3
4.7
DCR
(Ω MAX)
0.041
0.054
0.068
0.170
0.116
0.174
0.060
0.097
0.060
0.260
0.17
0.20
MAX DC
CURRENT (A)
0.85
0.75
0.90
0.78
0.950
0.770
1.00
0.79
1.08
0.92
1.00
0.95
SIZE
W × L × H (mm 3 )
3.2 × 3.2 × 2.0
3.2 × 3.2 × 1.2
4.4 × 5.8 × 1.2
2.5 × 3.2 × 2.0
2.5 × 3.2 × 2.0
4.5 × 5.4 × 1.2
(40% of 600mA).
I L =
V OUT 1– OUT
V IN
? V OUT ( V IN – V OUT ) ? 1/2
I OUT(MAX) ?
?
V OUT = I L ESR +
1 V
f ?L
(1)
The DC current rating of the inductor should be at least
equal to the maximum load current plus half the ripple
current to prevent core saturation. Thus, a 720mA rated
inductor should be enough for most applications (600mA +
120mA). For better ef?ciency, choose a low DC resistance
inductor. The inductor value also has an effect on Burst
Mode operation. The transition to low current operation be-
gins when the inductor current peaks fall to approximately
200mA. Lower inductor values (higher ΔI L ) will cause this
to occur at lower load currents, which can cause a dip in
ef?ciency in the upper range of low current operation. In
Burst Mode operation, lower inductance values will cause
the burst frequency to increase.
Inductor Core Selection
Different core materials and shapes will change the
size/current and price/current relationship of an induc-
tor. Toroid or shielded pot cores in ferrite or permalloy
materials are small and don’t radiate much energy, but
generally cost more than powdered iron core inductors
with similar electrical characteristics. The choice of which
style inductor to use often depends more on the price vs
size requirements and any radiated ?eld/EMI requirements
C IN and C OUT Selection
In continuous mode, the source current of the top MOSFET
is a square wave of duty cycle V OUT /V IN . To prevent large
voltage transients, a low ESR input capacitor sized for the
maximum RMS current must be used. The maximum RMS
capacitor current is given by:
C IN Required I RMS
V IN
This formula has a maximum at V IN = 2V OUT , where
I RMS = I OUT /2. This simple worst-case condition is common-
ly used for design because even signi?cant deviations do
not offer much relief. Note that the capacitor manufacturer’s
ripple current ratings are often based on 2000 hours of
life. This makes it advisable to further derate the capacitor,
or choose a capacitor rated at a higher temperature than
required. Always consult the manufacturer if there is any
question. The selection of C OUT is driven by the required
effective series resistance (ESR). Typically, once the ESR
requirement for C OUT has been met, the RMS current
rating generally far exceeds the I RIPPLE(P-P) requirement.
The output ripple DV OUT is determined by:
1
8 ? f ? C OUT
than on what the LTC3409 requires to operate. Table 1
shows some typical surface mount inductors that work
well in LTC3409 applications.
3409fc
10
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3410BESC6-1.8#TRPBF | IC REG BUCK SYNC 1.8V .3A SC70-6 |
| LTC3411AIMS#TRPBF | IC REG BUCK SYNC ADJ 10MSOP |
| LTC3411IMS#TRPBF | IC REG BUCK SYNC ADJ 10MSOP |
| LTC3412IFE#TRPBF | IC REG BUCK SYNC ADJ 16TSSOP |
| LTC3413IFE#TRPBF | IC REG BUCK SYNC ADJ 3A 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3410 | 制造商:LINER 制造商全称:Linear Technology 功能描述:2.25MHz, 300mA Synchronous Step-Down Regulator in SC70 |
| LTC3410-1.875 | 制造商:LINER 制造商全称:Linear Technology 功能描述:2.25MHz, 300mA Synchronous Step-Down Regulator in SC70 |
| LTC3410B | 制造商:LINER 制造商全称:Linear Technology 功能描述:2.25MHz, 300mA Synchronous Step-Down Regulator in SC70 |
| LTC3410BESC6#PBF | 制造商:Linear Technology 功能描述: |
| LTC3410BESC6#TR | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 2.5V to 5.5V 6-Pin SC-70 T/R |
发布紧急采购，3分钟左右您将得到回复。