- 您现在的位置：买卖IC网 > PDF目录14105 > LTC3411AEMS#TRPBF (Linear Technology)IC REG BUCK SYNC ADJ 10MSOP PDF资料下载
参数资料
| 型号： | LTC3411AEMS#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/22页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 10MSOP |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 5 V |
| 输入电压： | 2.5 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 2.5MHz |
| 电流 - 输出： | 1.25A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 10-MSOP |
LTC3411A
APPLICATIONS INFORMATION
V OUT ?
V OUT
f O ? Δ I L
V IN(MAX) ?
A general LTC3411A application circuit is shown in
Figure 4. External component selection is driven by the load
requirement, and begins with the selection of the inductor
L1. Once L1 is chosen, C IN and C OUT can be selected.
Operating Frequency
Selection of the operating frequency is a trade-off between
efficiency and component size. High frequency operation
allows the use of smaller inductor and capacitor values.
Operation at lower frequencies improves efficiency by
reducing internal gate charge losses but requires larger
inductance values and/or capacitance to maintain low
output ripple voltage.
The operating frequency, f O , of the LTC3411A is determined
by an external resistor that is connected between the R T
pin and ground. The value of the resistor sets the ramp
current that is used to charge and discharge an internal
timing capacitor within the oscillator and can be calculated
by using the following equation:
A reasonable starting point for setting ripple current is
Δ I L = 0.4 ? I OUT(MAX) , where I OUT(MAX) is 1.25A. The largest
ripple current Δ I L occurs at the maximum input voltage. To
guarantee that the ripple current stays below a specified
maximum, the inductor value should be chosen according
to the following equation:
?
L = ? ? 1 ? ?
?
The inductor value will also have an effect on Burst Mode
operation. The transition from low current operation
begins when the peak inductor current falls below a level
set by the burst clamp. Lower inductor values result in
higher ripple current which causes this to occur at lower
load currents. This causes a dip in efficiency in the upper
range of low current operation. In Burst Mode operation,
lower inductance values will cause the burst frequency
to increase.
R T = 5 ? 10 7 (f O ) –1.6508 (kΩ),
where f O is in kHz, or can be selected using Figure 1.
The maximum usable operating frequency is limited by
the minimum on-time and the duty cycle. This can be
calculated as:
5000
4500
4000
3500
3000
2500
2000
T A = 25°C
f O(MAX) ≈ 6.67 ?
V OUT
V IN(MAX)
(MHz)
1500
1000
500
The minimum frequency is internally set at around 200kHz.
0
0
400
800 1200
R T (k )
1600
? ? 1 ? OUT ?
Δ I L =
Inductor Selection
The operating frequency, f O , has a direct effect on the in-
ductor value, which in turn influences the inductor ripple
current Δ I L :
V OUT ? V ?
f O ? L ? V IN ?
The inductor ripple current decreases with larger induc-
tance or frequency, and increases with higher V IN or V OUT .
Accepting larger values of ΔI L allows the use of lower
inductances, but results in higher output ripple voltage,
greater core loss and lower output capability.
3411A F01
Figure 1. Frequency vs R T
Inductor Core Selection
Different core materials and shapes will change the
size/current and price/current relationship of an induc-
tor. Toroid or shielded pot cores in ferrite or permalloy
materials are small and don’t radiate much energy, but
generally cost more than powdered iron core inductors
with similar electrical characteristics. The choice of which
style inductor to use often depends more on the price vs
size requirements and any radiated field/EMI requirements
than on what the LTC3411A requires to operate. Table 1
3411afc
10
For more information www.linear.com/LTC3411A
相关PDF资料 |
PDF描述 |
|---|---|
| VI-BNX-EX-F4 | CONVERTER MOD DC/DC 5.2V 75W |
| LTC3411AEDD#TRPBF | IC REG BUCK SYNC ADJ 1.25A 10DFN |
| AP1501-K5L-U | IC REG BUCK ADJ 3A TO263-5 |
| MAX6868UK19D6S+T | IC MPU SUPERVISOR SOT23-5 |
| VI-BNX-EW-F1 | CONVERTER MOD DC/DC 5.2V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3411AIDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 1.25A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3411AIDD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 1.25A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3411AIDD-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.25A, 4MHz, Synchronous Step-Down DC/DC Converter |
| LTC3411AIDD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.25A, 4MHz, Synchronous Step-Down DC/DC Converter |
| LTC3411AIMS#PBF | 功能描述:IC REG BUCK SYNC ADJ 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。