参数资料
| 型号： | LTC3411AIMS#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/22页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 10MSOP |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 5 V |
| 输入电压： | 2.5 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 2.5MHz |
| 电流 - 输出： | 1.25A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 10-MSOP |
LTC3411A
APPLICATIONS INFORMATION
L =
? ? 1 ?
? = 2 μ H
3) I 2 R Losses are calculated from the DC resistances of
the internal switches, R SW , and external inductor, R L . In
continuous mode, the average output current flowing
through inductor L is “chopped” between the internal top
and bottom switches. Thus, the series resistance look-
ing into the SW pin is a function of both top and bottom
MOSFET R DS(ON) and the duty cycle (DC) as follows:
R SW = (R DS(ON) TOP)(DC) + (R DS(ON) BOT)(1 – DC)
The R DS(ON) for both the top and bottom MOSFETs can
be obtained from the Typical Performance Characteristics
curves. Thus, to obtain I 2 R losses:
I 2 R losses = I OUT 2(R SW + R L )
4) Other “hidden” losses such as copper trace and internal
battery resistances can account for additional efficiency
degradations in portable systems. It is very important
to include these “system” level losses in the design of a
system. The internal battery and fuse resistance losses can
be minimized by making sure that C IN has adequate charge
storage and very low ESR at the switching frequency. Other
losses including diode conduction losses during dead-time
and inductor core losses which generally account for less
than 2% total additional loss.
Thermal Considerations
In a majority of applications, the LTC3411A does not
dissipate much heat due to its high efficiency. However,
in applications where the LTC3411A is running at high
ambient temperature with low supply voltage and high
duty cycles, such as in dropout, the heat dissipated may
exceed the maximum junction temperature of the part. If
the junction temperature reaches approximately 150°C,
both power switches will be turned off and the SW node
will become high impedance.
To avoid the LTC3411A from exceeding the maximum junc-
tion temperature, the user will need to do some thermal
analysis. The goal of the thermal analysis is to determine
whether the power dissipated exceeds the maximum junction
temperature of the part. The temperature rise is given by:
T RISE = P D ? θ JA
The junction temperature, T J , is given by:
T J = T RISE + T AMBIENT
As an example, consider the case when the LTC3411A
is in dropout at an input voltage of 3.3V with a load cur-
rent of 1A. From the Typical Performance Characteristics
graph of Switch Resistance, the R DS(ON) resistance of the
P-channel switch is 0.15Ω. Therefore, power dissipated
by the part is:
P D = I 2 ? R DS(ON) = 150mW
The MS10 package junction-to-ambient thermal resistance,
θ JA , will be in the range of 100°C/W to 120°C/W. Therefore,
the junction temperature of the regulator operating in a
70°C ambient temperature is approximately:
T J = 0.15 ? 120 + 70 = 88°C
Remembering that the above junction temperature is
obtained from an R DS(ON) at 25°C, we might recalculate
the junction temperature based on a higher R DS(ON) since
it increases with temperature. However, we can safely as-
sume that the actual junction temperature will not exceed
the absolute maximum junction temperature of 125°C.
Design Example
As a design example, consider using the LTC3411A in a
portable application with a Li-Ion battery. The battery pro-
vides a V IN = 2.5V to 4.2V. The load requires a maximum
of 1.25A in active mode and 10mA in standby mode. The
output voltage is V OUT = 2.5V. Since the load still needs
power in standby, Burst Mode operation is selected for
good low load efficiency.
First, calculate the timing resistor for 1MHz operation:
R T = 5 ? 10 7 (10 3 ) –1.6508 = 557.9k
Use a standard value of 549k. Next, calculate the inductor
value for about 40% ripple current at maximum V IN :
2.5V ? 2.5V ?
1MHz ? 500mA ? 4.2V ?
Choosing the closest standard inductor value from a vendor
of 2.2μH, results in a maximum ripple current of:
? ? 1 ?
where P D is the power dissipated by the regulator and θ JA
is the thermal resistance from the junction of the die to
the ambient temperature.
Δ I L =
2.5V
1MHz ? 2.2 μ
?
?
2.5V ?
4.2V ? ?
= 460mA
3411afc
16
For more information www.linear.com/LTC3411A
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3411IMS#TRPBF | IC REG BUCK SYNC ADJ 10MSOP |
| LTC3412IFE#TRPBF | IC REG BUCK SYNC ADJ 16TSSOP |
| LTC3413IFE#TRPBF | IC REG BUCK SYNC ADJ 3A 16TSSOP |
| LTC3414MPFE#TRPBF | IC REG BUCK SYNC ADJ 4A 20TSSOP |
| LTC3415EUHF#TRPBF | IC REG BUCK SYNC ADJ 7A 38QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3411EDD | 功能描述:IC REG BUCK SYNC ADJ 1.25A 10DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3411EDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 1.25A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3411EDD#PBF | 制造商:Linear Technology 功能描述:DC/DC Converter IC |
| LTC3411EDD#TR | 功能描述:IC REG BUCK SYNC ADJ 1.25A 10DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3411EDD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 1.25A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。