- 您现在的位置：买卖IC网 > PDF目录14111 > LTC3448EDD#PBF (Linear Technology)IC REG BUCK SYNC ADJ 0.6A 8DFN PDF资料下载
参数资料
| 型号： | LTC3448EDD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 0.6A 8DFN |
| 标准包装： | 121 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 5.2 V |
| 输入电压： | 2.5 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.5MHz ~ 2.25MHz |
| 电流 - 输出： | 600mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 8-DFN-EP（3x3） |
LTC3448
APPLICATIO S I FOR ATIO
Inductor Core Selection
Different core materials and shapes will change the size/
current and price/current relationship of an inductor.
Toroid or shielded pot cores in ferrite or permalloy mate-
rials are small and don’t radiate much energy, but gener-
ally cost more than powdered iron core inductors with
similar electrical characteristics. The choice of which style
inductor to use often depends more on the price vs size
requirements and any radiated field/EMI requirements
temperature than required. Always consult the manufac-
turer if there is any question.
The selection of C OUT is driven by the required effective
series resistance (ESR). Typically, once the ESR require-
ment for C OUT has been met, the RMS current rating
generally far exceeds the I RIPPLE(P-P) requirement. In any
case, if LDO mode is enabled, the value of C OUT must have
a minimum value of 2 μ F to ensure loop stability. The
output ripple ? V OUT is determined by:
? V OUT ? ? I L ? ESR +
8 fC OUT ?
than on what the LTC3448 requires to operate. Table 1
shows some typical surface mount inductors that work
well in LTC3448 applications.
?
?
1 ?
?
Table 1. Representative Surface Mount Inductors
PART VALUE DCR MAX DC SIZE
NUMBER ( μ H) ( ? MAX) CURRENT (A) W × L × H (mm 3 )
CDRH3D16 2.2 0.075 1.20
Sumida 1.5 0.043 1.55 3.8 × 3.8 × 1.8
where f = operating frequency, C OUT = output capacitance
and ? I L = ripple current in the inductor. For a fixed output
voltage, the output ripple is highest at maximum input
voltage since ? I L increases with input voltage.
3.3
4.7
0.110
0.162
1.10
0.90
Aluminum electrolytic and dry tantalum capacitors are
Sumida
CMD4D06
Coilcraft
ME3220
Murata
LQH3C
2.2
3.3
4.7
2.2
3.3
4.7
1.0
2.2
4.7
0.116
0.174
0.216
0.104
0.138
0.190
0.060
0.097
0.150
0.950
0.770
0.750
1.8
1.3
1.2
1.00
0.79
0.65
3.5 × 4.3 × 0.8
2.5 × 3.2 × 2.0
2.5 × 3.2 × 2.0
both available in surface mount configurations. In the case
of tantalum, it is critical that the capacitors are surge tested
for use in switching power supplies. An excellent choice is
the AVX TPS series of surface mount tantalum. These are
specially constructed and tested for low ESR so they give
the lowest ESR for a given volume. Other capacitor types
include Sanyo POSCAP, Kemet T510 and T495 series, and
Sprague 593D and 595D series. Consult the manufacturer
for other specific recommendations.
C IN and C OUT Selection
In continuous mode, the source current of the top MOS-
FET is a square wave of duty cycle V OUT /V IN . To prevent
large voltage transients, a low ESR input capacitor sized
for the maximum RMS current must be used. The maxi-
mum RMS capacitor current is given by:
Using Ceramic Input and Output Capacitors
Higher values, lower cost ceramic capacitors are now
becoming available in smaller case sizes. Their high ripple
current, high voltage rating and low ESR make them ideal
for switching regulator applications. Because the
) ]
C IN required I RMS ? I OMAX
[
V OUT ( V IN ? V OUT
V IN
1 / 2
LTC3448’s control loop does not depend on the output
capacitor’s ESR for stable operation, ceramic capacitors
can be used freely to achieve very low output ripple and
small circuit size.
This formula has a maximum at V IN = 2V OUT , where
I RMS = I OUT /2. This simple worst-case condition is com-
monly used for design. Note that the capacitor
manufacturer’s ripple current ratings are often based on
2000 hours of life. This makes it advisable to further derate
the capacitor, or choose a capacitor rated at a higher
However, care must be taken when ceramic capacitors are
used at the input and the output. When a ceramic capacitor
is used at the input and the power is supplied by a wall
adapter through long wires, a load step at the output can
induce ringing at the input, V IN . At best, this ringing can
couple to the output and be mistaken as loop instability. At
3448f
10
相关PDF资料 |
PDF描述 |
|---|---|
| VI-BN1-EX-F3 | CONVERTER MOD DC/DC 12V 75W |
| VI-BN1-EW-F3 | CONVERTER MOD DC/DC 12V 100W |
| ECM28DTAT | CONN EDGECARD 56POS R/A .156 SLD |
| MAX6867UK46D5L+T | IC MPU SUPERVISOR SOT23-5 |
| LQH6PPN1R0N43L | INDUCTOR POWER 1UH 4.3A 2424 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3448EMS8E | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3448EMS8E#PBF | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3448EMS8E#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3450 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Triple Output Power Supply for Small TFT-LCD Displays |
| LTC3450EUD | 功能描述:IC CONV PS TRIPLE TFT/LCD 16QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。