- 您现在的位置：买卖IC网 > PDF目录13079 > LTC3450EUD (Linear Technology)IC CONV PS TRIPLE TFT/LCD 16QFN PDF资料下载
参数资料
| 型号： | LTC3450EUD |
| 厂商： | Linear Technology |
| 文件页数： | 6/12页 |
| 文件大小： | 0K |
| 描述： | IC CONV PS TRIPLE TFT/LCD 16QFN |
| 标准包装： | 121 |
| 应用： | 转换器，TFT，LCD |
| 输入电压： | 1.5 V ~ 4.6 V |
| 输出数： | 3 |
| 输出电压： | 5.1V，-5V，±10V，±15V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-QFN-EP（3x3） |
| 包装： | 管件 |
LTC3450
PI FU CTIO S
C3 + (Pin 1): Charge Pump Inverter Flying Capacitor Posi-
tive Node. The charge pump inverter flying capacitor is
connected between C3 + and C3 – . The voltage on C3 + will
alternate between GND and V INV at an approximate 50%
duty cycle while the inverting charge pump is operating.
Use a 10nF or larger X5R type ceramic capacitor for best
results.
C3 – (Pin 2): Charge Pump Inverter Flying Capacitor Nega-
tive Node. The charge pump inverter flying capacitor is
connected between C3 + and C3 – . The voltage on C3 – will
alternate between GND and V NEG at an approximate 50%
duty cycle while the inverting charge pump is operating.
Use a 10nF or larger X5R type ceramic capacitor for best
results.
V NEG (Pin 3): Charge Pump Inverter Output. V NEG can be
either – 5V or –10V depending on where V INV is con-
nected. V NEG should be bypassed to GND with at 0.1 μ F or
larger X5R type ceramic capacitor. V NEG can also be
configured for –15V with two external low current Schottky
diodes (see Applications section).
MODE(Pin4): DriveMODEhightoforcetheLTC3450into
high power (scan) mode. Drive MODE low to force the
LTC3450 into low power (blank) mode. The output volt-
ages remain active with the MODE pin driven low but with
reduced output current capability. MODE must be pulled
up to V IN or higher on initial application of power in order
for proper initialization to occur.
SHDN (Pin 5): Master Shutdown Input for the LTC3450.
Driving SHDN low disables all IC functions and reduces
quiescent current from the battery to less than 2 μ A. Each
generated output voltage is actively discharged to GND in
shutdown through internal pull down devices. An optional
RC network on SHDN provides a slower ramp up of the
boost converter inductor current during startup (soft-start).
V IN (Pin 6): Input Supply to the LTC3450. Connect V IN to
a voltage source between 1.5V and 4.6V. Bypass V IN to
GND with a 2.2 μ F X5R ceramic capacitor.
V OUT (Pin 7): Main 5.1V Output of the Boost Regulator and
SW (Pin 8): Switch Pin. Connect the inductor between SW
and V IN . Keep PCB trace lengths as short and wide as
possible to reduce EMI and voltage overshoot. If the
inductor current falls to zero, the internal P-channel
MOSFET synchronous rectifier is turned off to prevent
reverse charging of the inductor and an internal switch
connects SW to V IN to reduce EMI.
GND (Pin 9): Signal and Power Ground for the LTC3450.
Provide a short direct PCB path between GND and the
output filter capacitor(s) on V OUT , V2X, V3X and V NEG .
C1 – (Pin 10): Charge Pump Doubler Flying Capacitor
Negative Node. The charge pump doubler flying capacitor
is connected between C1 + and C1 – . The voltage on C1 – will
alternate between GND and V OUT at an approximate 50%
duty cycle while the charge pump is operating. Use a 10nF
or larger X5R type ceramic capacitor for best results.
C1 + (Pin 11): Charge Pump Doubler Flying Capacitor
Positive Node. The charge pump doubler flying capacitor
is connected between C1 + and C1 – . The voltage on C1 + will
alternate between V OUT and V2X at an approximate 50%
duty cycle while the charge pump is operating. Use a 10nF
or larger X5R type ceramic capacitor for best results.
V2X (Pin 12): Charge Pump Doubler Output. This output
is 10.2V (nom) at no load and is capable of delivering up
to 500 μ A to a load. V2X should be bypassed to GND with
a 0.47 μ F X5R type ceramic capacitor.
C2 – (Pin 13): Charge Pump Tripler Flying Capacitor Nega-
tive Node. The charge pump tripler flying capacitor is
connected between C2 + and C2 – . The voltage on C2 – will
alternate between GND and V OUT at an approximate 50%
duty cycle while the charge pump is operating. Use a 10nF
or larger X5R type ceramic capacitor for best results.
C2 + (Pin 14): Charge Pump Tripler Flying Capacitor Posi-
tive Node. The charge pump tripler flying capacitor is
connected between C2 + and C2 – . The voltage on C2 + will
alternate between V2X and V3X at an approximate 50%
duty cycle while the charge pump is operating. Use a 10nF
or larger X5R type ceramic capacitor for best results.
Input to the Voltage Doubler Stage. Bypass V OUT with a low
ESR, ESL ceramic capacitor (X5R type) between 2.2 μ F and
10 μ F.
3450fa
6
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J5H-EZ-B1 | CONVERTER MOD DC/DC 52V 25W |
| RCB66DHRN-S621 | CONN EDGECARD EXTEND 132POS .050 |
| LT1942EUF#PBF | IC REG SW QUAD TFT LCD 24-QFN |
| MIC37252WU | IC REG LDO ADJ 2.5A TO-263 |
| MIC9131YQS TR | IC CTRLR DC-DC PWM HV HS 16-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3450EUD#PBF | 功能描述:IC CONV PS TRIPLE TFT/LCD 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
| LTC3450EUD#TR | 功能描述:IC CONV PS TRIPLE TFT/LCD 16QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC3450EUD#TRPBF | 功能描述:IC CONV PS TRIPLE TFT/LCD 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC3452 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous Buck-Boost MAIN/CAMERA White LED Driver |
| LTC3452EUF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous Buck-Boost MAIN/CAMERA White LED Driver |
发布紧急采购，3分钟左右您将得到回复。