- 您现在的位置：买卖IC网 > PDF目录1829 > LTC3499BEDD#TRPBF (Linear Technology)IC REG BOOST SYNC ADJ 0.75A 8DFN PDF资料下载
参数资料
| 型号： | LTC3499BEDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SYNC ADJ 0.75A 8DFN |
| 标准包装： | 2,500 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2 V ~ 6 V |
| 输入电压： | 1.8 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 1.2MHz |
| 电流 - 输出： | 750mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-DFN-EP（3x3） |
LTC3499/LTC3499B
OPERATION
I OUT(MAX) ?
Reverse-BatteryProtection
Connecting the battery backwards poses a severe problem
to most power converters. At a minimum the battery will
be quickly discharged. Almost all ICs have an inherent diode
from V IN (cathode) to ground (anode) which conducts ap-
preciable current when V IN drops more than 0.7V below
ground. Under this condition the integrated circuit will
most likely be damaged due to the excessive current draw.
There exists the possibility for the battery and circuitry
powered by the device to also be damaged. The LTC3499/
LTC3499B have integrated circuitry which allows negligible
current flow under a reverse-battery condition, protecting
the battery, device and circuitry attached to the output. A
graph of the reverse-battery current drawn is shown in
the Typical Performance Characteristics.
Discrete methods of reverse battery protection put ad-
ditional dissipative elements in the high current path
reducing efficiency while increasing component count
to implement protection. The LTC3499/LTC3499B do not
suffer from either of these drawbacks.
Burst Mode Operation (LTC3499 only)
Portable devices frequently spend extended time in low
power or stand-by mode, only drawing high power when
specific functions are enabled. In order to improve battery
life in these types of products, high power converter ef-
ficiency needs to be maintained over a wide output power
range. In addition to its high efficiency at moderate and
heavy loads, the LTC3499 includes automatic Burst Mode
operation that improves efficiency of the power converter
at light loads. Burst Mode operation is initiated if the
output load current falls below an internally programmed
threshold (see Typical Performance graph, Output Load
Burst Mode Threshold vs V IN ). Once initiated the Burst
Mode operation circuitry shuts down most of the circuitry
in the LTC3499, keeping alive only the circuitry required
to monitor the output voltage.
This state is referred to as sleep. In sleep, the LTC3499
only draws 20μA from the input supply, greatly enhancing
efficiency. When the output has drooped approximately
1% from its nominal regulation point, the LTC3499 wakes
up and commences normal PWM operation. The output
capacitor will recharge causing the LTC3499 to re-enter
sleep if the output load current remains less than the
sleep threshold. The frequency of this intermittent PWM
(or burst) operation is proportional to load current.
Therefore, as the load current drops further below the
burst threshold, the LTC3499 operates in PWM mode
less frequently. When the load current increases above
the burst threshold, the LC3499 will resume continuous
PWM operation seamlessly.
Referring to the Functional Block Diagram, an optional
capacitor, C FF , between V OUT and FB in some circumstances
can reduce peak-to-peak V OUT ripple and input quiescent
current during Burst Mode operation. Typical values for
C FF range from 10pF to 220pF.
Output Disconnect and Inrush Current Limiting
The LTC3499/LTC3499B are designed to allow true output
disconnect by eliminating body diode conduction of the
internal P-channel MOSFET switch. This allows V OUT to
go to zero volts during shutdown without drawing any
current from the input source. It also provides for inrush
current limiting at turn-on, minimizing surge current seen
by the input supply.
V IN > V OUT Operation
The LTC3499/LTC3499B will maintain voltage regulation
when the input voltage is above the output voltage. This is
achieved by terminating the switching on the synchronous
P-channel MOSFET and applying V IN statically on the gate.
This will ensure the volts ? seconds of the inductor will
reverse during the time current is flowing to the output.
Since this mode will dissipate more power in the IC, the
maximum output current is limited in order to maintain
an acceptable junction temperature:
125 – T A
θ JA ? ( ( V IN + 1.5 ) – V OUT )
where T A = ambient temperature and θ JA is the package
thermal resistance (45°C/W for the DD8 and 160°C/W
for the MS8).
For example at V IN = 4.5V, V OUT = 3.3V and T A = 85°C in
the DD8 package, the maximum output current is 330mA.
3499fc
9
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3520EUF#PBF | IC REG BUCK BOOST SYNC ADJ 24QFN |
| LTC3521IFE#TRPBF | IC REG BUCK BST SYNC ADJ 20TSSOP |
| LTC3522EUD#TRPBF | IC REG BUCK BOOST SYNC ADJ 16QFN |
| LTC3523EUD-2#TRPBF | IC REG BUCK BOOST SYNC ADJ 16QFN |
| LTC3525ESC6-3.3#TRPBF | IC REG BST SYNC 3.3V 0.4A SC70-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3499BEMS8 | 制造商:LINER 制造商全称:Linear Technology 功能描述:750mA Synchronous Step-Up DC/DC Converters with Reverse-Battery Protection |
| LTC3499BEMS8#PBF | 功能描述:IC REG BST SYNC ADJ 0.75A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3499BEMS8#TRPBF | 功能描述:IC REG BST SYNC ADJ 0.75A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3499EDD | 制造商:LINER 制造商全称:Linear Technology 功能描述:750mA Synchronous Step-Up DC/DC Converters with Reverse-Battery Protection |
| LTC3499EDD#PBF | 功能描述:IC REG BOOST SYNC ADJ 0.75A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
发布紧急采购，3分钟左右您将得到回复。