- 您现在的位置：买卖IC网 > PDF目录79982 > LTC3521IFE#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, 1350 kHz SWITCHING FREQ-MAX, PDSO20 PDF资料下载
参数资料
| 型号： | LTC3521IFE#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, 1350 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封装： | 4.40 MM, LEAD FREE, PLASTIC, TSSOP-20 |
| 文件页数： | 5/22页 |
| 文件大小： | 1476K |
| 代理商： | LTC3521IFE#TRPBF |
LTC3521
13
3521fa
Burst Mode Operation
With the PWM pin held low, the buck-boost converter
operatesutilizingavariablefrequencyswitchingalgorithm
designed to improve efficiency at light load and reduce
the standby current at zero load. In Burst Mode operation,
the inductor is charged with fixed peak amplitude current
pulses. These current pulses are repeated as often as
necessary to maintain the output regulation voltage. The
maximum output current which can be supplied in Burst
Mode operation is dependent upon the input and output
voltage as given by the following formula:
IOUT(MAX),BURST =
0.1 VIN
VIN + VOUT
A
( )
In Burst Modeoperation,the erroramplifier is not used but
is instead placed in a low current standby mode to reduce
supply current and improve light load efficiency.
Soft-Start
The buck-boost converter has an internal voltage mode
soft-start circuit with a nominal duration of 600μs. The
converter remains in regulation during soft-start and will
therefore respond to output load transients that occur
during this time. In addition, the output voltage rise time
has minimal dependency on the size of the output capaci-
tor or load. During soft-start, the buck-boost converter is
forced into PWM operation regardless of the state of the
PWM pin.
PGOOD Comparator
The PGOOD1 pin is an open-drain output which indicates
the status of the buck-boost converter. In Burst Mode
operation (PWM = Low), the PGOOD1 open-drain output
will pull low when the feedback voltage falls 9% below the
regulationvoltage.Thereisapproximately3%hysteresisin
this threshold when the output voltage is returning good.
In addition, there is a 60μs typical deglitching delay to
prevent false trips due to short duration voltage transients
in response to load steps.
In PWM mode, operation of the PGOOD1 comparator is
complicated by the fact that the feedback pin voltage is
driven to the reference voltage independent of the output
OPERATION
voltage through the action of the voltage mode error am-
plifier. Since the soft-start is voltage mode, the feedback
voltage will track the output voltage correctly during
soft-start, and the PGOOD1 output will correctly indicate
the point at which the buck-boost attains regulation at the
end of soft-start. Therefore, the PGOOD1 output can be
utilized for sequencing purposes. Once in regulation, the
feedback voltage will no longer track the output voltage,
and the PGOOD1 pin will not directly respond to a loss
of regulation in the output. However, the only means by
which a loss of regulation can occur is if the current limit
has been reached, thereby preventing the buck-boost
converter from delivering the required output current.
In such cases, the occurrence of current limit will cause
the PGOOD1 flag to fall indicating a fault state. There can
be cases, however, when the buck-boost converter is
continuously in current limit, causing the PGOOD1 output
to pull low, while the output voltage still remains slightly
above the PGOOD1 comparator trip point.
ThePGOOD1outputalsopullslowduringovertemperature
shutdown, undervoltage lockout or if the SHDN1 pin is
pulled low.
COMMON FUNCTIONS
Thermal Shutdown
If the die temperature exceeds 150°C, all three converters
will be disabled. All power devices will be turned off and
all switch nodes will be high impedance. The soft-start
circuits for all three converters are reset during thermal
shutdown to provide a smooth recovery once the over-
temperature condition is eliminated. All three converters
will restart (if enabled) when the die temperature drops
to approximately 140°C.
Undervoltage Lockout
If the supply voltage decreases below 1.7V (typical) then
all three converters will be disabled and all power devices
will be turned off. The soft-start circuits for all three con-
verters are reset during undervoltage lockout to provide
a smooth restart once the input voltage rises above the
undervoltage lockout threshold.
相关PDF资料 |
PDF描述 |
|---|---|
| LS4501-9PD6TB1 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LK2320-7EPD2TB1 | 2-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK2540-7EPD2TB1 | 2-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LS1001-7EPD7T | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LS1301-9ERD1TB1 | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3521IUF#PBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3521IUF#TRPBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3522 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous 400mA Buck-Boost and 200mA Buck Converters |
| LTC3522EUD | 制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous 400mA Buck-Boost and 200mA Buck Converters |
| LTC3522EUD#PBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
发布紧急采购，3分钟左右您将得到回复。